Hostname: page-component-6bf8c574d5-7jkgd Total loading time: 0 Render date: 2025-02-22T17:00:12.226Z Has data issue: false hasContentIssue false
  • English
  • Français

Pressure Casting of Ni3Al/Al2O3 Composites

Published online by Cambridge University Press:  26 February 2011

Said Nourbakhsh ,
Fei-Lin Liang  and
Harold Margolin
Said Nourbakhsh
Affiliation:
Department of Metallurgy and Materials Science, Polytechnic University, 333 Jay Street, Brooklyn, NY 11201
Fei-Lin Liang
Affiliation:
Department of Metallurgy and Materials Science, Polytechnic University, 333 Jay Street, Brooklyn, NY 11201
Harold Margolin
Affiliation:
Department of Metallurgy and Materials Science, Polytechnic University, 333 Jay Street, Brooklyn, NY 11201
Get access

Abstract

A series of Du Pont PRD-166 and FP fiber reinforced Ni and nickel aluminide matrix composites, containing Ti or Y as a wetting agent, were produced by pressure casting. Modulus values determined under compression varied from 273 to 287 GPa in a direction parallel to the fibers and ranged from 148 to 159 in a direction normal to the fibers. Modulus values parallel to the fiber direction were approximately 5% lower than that predicted by the rule-of-mixtures. The much lower values of modulus normal to the fibers has been attributed to a number of sources which include fiber/matrix and fiber/fiber debonding and stress concentration resulting from voids existing at fiber/fiber bonds. It was observed, qualitatively, that good bonding between matrix and fiber occurred when Ti diffused from the matrix into fibers. The presence of Al in the matrix tended to inhibit Ti diffusion, increasingly as Al content increased. Thus fiber/matrix bond strength was poorer in the aluminides than in an alloy containing no Al. Y was not found to improve bonding, and an interface reaction zone was obserced in some areas where liquid metal initially entered the fiber preform.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 133: Symposium H – High-Temperature Ordered Intermetallic Alloys III , 1988 , 459
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Bose, A., Moore, B., German, R.M. and Stoloff, N.S., J. Metals 40 (4), 14(1988).Google Scholar
2. Bose, A. and German, R.M., Advanced Materials and Manufac. Processes 3 (1), 37(1988).Google Scholar
3. Cornie, J.A., Mortensen, A., Gungor, M. and Flemings, M.C. in Fifth International Conf. on Composite Materials, edited by W.C. Harrigan, J. Strife and A.K. Dhingra (The Metallurgical Society of AIME, 1985), pp. 809.Google Scholar
4. Clyne, T.W. and Manson, J.F., Met. Trans. 18A, 1519(1987).CrossRefGoogle Scholar
5. Fukunaga, H. and Kuriyama, M., Bull. Jap. Soc. of Mech Eng. 25, 842(1982).CrossRefGoogle Scholar
6. Nourbakhsh, S., Liang, F.L. and Margolin, H., J. Phys. E: Sci. Instru. 21, 898(1988).CrossRefGoogle Scholar
7. Nourbakhsh, S., Liang, F.L. and Margolin, H., Advanced Materials and Manufacturing Processes 3 (1), 57(1988).CrossRefGoogle Scholar
8. Romine, J.C., Ceramic Engineering and Science Proceedings 8 (7–8), 755 (1987).CrossRefGoogle Scholar
9. Nourbakhsh, S., Margolin, H. and Liang, F.L., Submitted for Publication in Met. Trans. A.Google Scholar
10. Stoloff, N.S., High Temperature Ordered Intermetallic Alloys, edited by Koch, C.C., Liu, C.T. and Stoloff, N.S. (MRS 39, 1984), pp. 3.Google Scholar
11. Kingery, W.D., Introduction to Ceramics, John Wiley and Sons, 1960.Google Scholar
12. Kubaschewski, O. and Alcock, C.B., Metallurgical Thermochemistry, 5th edition, Pergamon Press, 1979.Google Scholar