Hostname: page-component-6bf8c574d5-gr6zb Total loading time: 0 Render date: 2025-02-22T17:00:34.373Z Has data issue: false hasContentIssue false
  • English
  • Français

Production and Characterization of FE-NI-CO-TI Shape Memory Springs with One- and Two-Way Effect

Published online by Cambridge University Press:  25 February 2011

Norbert Jost
Norbert Jost*
Affiliation:
Oelbachtal 25, D-4630 Bochum 7, Federal Republic of Germany (formerly: Institute for Materials, Ruhr-University Bochum)
Get access

Abstract

It has been shown that ausaged Fe-Ni-Co-Ti alloys exhibit a reversible martensitic transformation with a small temperature hysteresis between the forward and the reverse transformation. This is due to the precipitation of small coherent (Ni,Co,Fe)3Ti particles. On the one hand they lead to a very effective precipitation hardening of the austenite and on the other hand to high elastic back stresses after shearing together with the martensite into a metastable structure. The martensitic morphology in such states is typically lathlike (thin plate martensite).

While yield stress and tensile strength increase during ausaging, the toughness, especially the elongation at fracture changes for the worse. The results of this work show that this can be prevented by a combined thermo-mechanical treatment. At the same time a remarkable twoway shape memory effect can be observed.

For practical applications the use of springs seems the best way for this type of Fe-based alloys because the recovery strain is low in comparison to Ni-Ti alloys. On the other side, due to the special transformation mechanism in Fe-Ni-Co-Ti alloys it can be assumed that the possible power in the two-way-effect should nearly reach the value of that obtained in binary Ni-Ti alloys.

Mechanical and thermal properties of different springs made from Fe-Ni-Co-Ti shape memory alloys were studied by means of special deformation tests. Thereby, the maximum obtainable power in the reversible shape-memory effect of the investigated springs was of special interest. The martensite morphologies were investigated by optical-microscopy.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 246: Symposium M – Shape-Memory Materials and Phenomena--Fundamental Aspects and Applications , 1991 , 337
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Maki, T., Kobayashi, K., Minato, M., Tamura, I., Scripta Met. 18 (1984) 1105–1109 CrossRefGoogle Scholar
[2] Koval, Y.U., Kokorin, V.V., Khandros, L.G., Fiz. met. metalloved. 48 (1979) 1309–1311 Google Scholar
[3] Jost, N., Metall 44 (1990) 17–22 Google Scholar
[4] Hornbogen, E., Jost, N., Proc. Europ. Symp. Martensitic Transformation and Shape Memory Properties, Aussois, France, (1991), in printGoogle Scholar
[5] Jost, N., Proc. Europ. Conf. The Martensitic Transformation in Science and Technology, Bochum, FRG, DGM-Verlag, Hornbogen, E., Jost, N. (eds.), (1989) 273–280 Google Scholar
[6] Jost, N., Proc. Int. Conf. Martensitic Transformations (ICOMAT 89), Sydney, Australia, Materials Science Forum, Vol. 56–58, Muddle, B.C. (ed.) 667–672 Google Scholar
[7] Jost, N., Hiuhner, M., Sonderbde. der Prakt. Metallo. 21 (1990), Petzow, G. (ed.) 191–204 Google Scholar
[8] Jost, N., see [4], in printGoogle Scholar
[9] Escher, K., Jost, N., see [5], 281–286 Google Scholar
[10] Jost, N., VDI-Fortschrittberichte, Series 5, No. 169, VDI-Verlag, Dtisseldorf 1989 Google Scholar
[11] Jost, N., Huhner, M., Pract. Met. 26 (1989) 295–306 Google Scholar
[12] Jost, N., in: Progress in Shape Memory, DGM-Verlag, Eucken, S. (ed.), (1991) in printGoogle Scholar
[13] Halter, K., Jost, N., Stalder, J.L., Wireworld 33 (1991), No. 6, 14–26 Google Scholar