Hostname: page-component-78c5997874-lj6df Total loading time: 0 Render date: 2024-11-10T08:59:25.221Z Has data issue: false hasContentIssue false
  • English
  • Français

Transient Fatigue Crack-Growth Behavior and Damage Zones in Zr-Based Bulk Metallic Glass

Published online by Cambridge University Press:  01 February 2011

Peter A. Hess  and
Reinhold H. Dauskardt
Peter A. Hess
Affiliation:
Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305
Reinhold H. Dauskardt
Affiliation:
Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305
Get access

Abstract

Fatigue crack propagation mechanisms of bulk metallic glasses (BMGs) are not well understood, limiting their use in safety-critical structural applications particularly where complex fatigue loading may occur. Accordingly, the present study examines the effects of variable amplitude fatigue loading associated with block loading and tensile overloads on fatigue crack-growth rates in a Zr-based BMG. Crack growth studies were conducted on compact tension specimens using computer control of the applied stress intensity range, ΔK. Fatigue crack closure loads, which represent the initial contact of mating crack surfaces during the unloading cycle, were continuously monitored during testing. Abrupt drops in ΔK were found to significantly decrease fatigue crack-growth rates far below equilibrium values, arresting growth completely at a ΔK twice the nominal fatigue threshold ΔKTH. Conversely, an abrupt increase in ΔK was found to accelerate fatigue crack-growth rates. The effects of roughness-induced crack closure were assessed and found to be consistent with the suppression or acceleration of growth rates. However, in order to fully explain the observed transient growth rate response, other mechanisms that may be related to the fatigue mechanism itself were also considered. Specifically, the nature of the fatigue crack tip damage zone was also investigated. As BMGs lack distributed plasticity at low temperatures, the plastic zone differs greatly from that seen in ductile crystalline materials, and its role in fatigue crack propagation mechanisms is examined.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 806: Symposium MM – Amorphous and Nanocrystalline Metals , 2003 , MM7.10
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Bruck, H.A., et al., Scripta Metallurgica et Materialia, 1994. 30(4): p. 429–34.Google Scholar
2. Gilbert, C.J., Schroeder, V., and Ritchie, R.O., Metallurgical and Materials Transactions A, 1999. 30A(7): p. 1739–53.Google Scholar
3. Flores, K.M. and Dauskardt, R.H., Scripta Materialia, 1999. 41(9): p. 937–43.Google Scholar
4. Lowhaphandu, P. and Lewandowski, J.J., Scripta Materialia, 1998. 38(12): p. 1811–1817.Google Scholar
5. Schroeder, V., Gilbert, C.J., and Ritchie, R.O., Scripta Materialia, 1999. 40(9): p. 1057–61.Google Scholar
6. Flores, K.M. and Dauskardt, R.H.. in Supercooled Liquid, Bulk Glassy and Nanocrystalline States of Alloys. 2000. Boston, MA, USA: Mater. Res. Soc.Google Scholar
7. Hess, P.A. and Dauskardt, R.H.. in Supercooled Liquids, Glass Transition, and Bulk Metallic Glasses. 2002. Boston, MA, USA: Mater. Res. Soc.Google Scholar
8. Zhang, H., et al., Materials Science and Engineering: A, 2003. 356: p. 173–180.Google Scholar
9. Hess, P.A. and Dauskardt, R.H., Acta Materialia - submitted, 2003.Google Scholar
10. Ward-Close, C.M., Blom, A.F., and Ritchie, R.O., Engineering Fracture Mechanics, 1989. 32(4): p. 613–638.Google Scholar
11. Chaki, T.K. and Li, J.C.M., Scripta Metallurgica, 1984. 18: p. 703–708.Google Scholar