Because of the interfacial interactions between mineral soil particles and soil organic matter (SOM), SOM occurs in various forms in the soil, and the mineral-associated and particulate forms are fundamental. Many recent studies have concentrated on the effects of SOM content and type on the geotechnical behavior of soil. However, the influence of SOM occurrence forms is not well understood, nor is there a scientific classification standard for SOM in geotechnical engineering. The main objectives of this study were to explore the effects of SOM occurrence forms on a few physical properties of clays to develop an engineering classification standard of SOM. First, this paper reviews the interfacial interaction mechanism, factors that influence the relation between mineral soil particles and SOM, and the classification method of SOM in soil science. Three predominant clays (montmorillonite, illite, and kaolinite) were then used as the matrix, and three groups of artificial soil samples with different SOM contents (wu ranging from 0 to 50% by weight) were prepared by adding peat. A chemical extraction method was used to determine the amount of different forms of SOM. Moreover, the Atterberg limits wL (wp) and thermal conductivity λ of artificial soil samples were tested. Based on the experimental results, the relationship between the form of SOM and these physical parameters was established. The experimental results show that the wL (wp) vs wu, and λ vs wu fitted curves were not monotonic but piecewise linear and could be divided into two straight lines with different slopes; wu corresponded to the inflection point of wL (wp) vs wu, and λ vs wu curves were closer to the threshold value wu,2. Finally, a simple engineering classification method of SOM is proposed.

Dioctahedral tosudite, a regular interstratification of dioctahedral chlorite-dioctahedral smectite, occurs associated with kaolin in the hydrothermal area of Delgado, Neutla, Mexico. Its composition corresponds to the formula:

$$\left( {S{I_{13.77}}A{L_{2.23}}} \right)A{L_8}{O_{40}}{\left( {OH} \right)_8} \cdot C{A_{0.39}}N{A_{0.03}}{K_{1.06}} \cdot \left( {A{L_{3.79}}F{E^{ + 3}}_{0.09}F{E^{ + 2}}_{0.06}M{G_{0.26}}} \right){\left( {OH} \right)_{12}}.$$

Several soil and reference smectites and vermiculites and one reference illite were examined by high-resolution transmission electron microscopy (HRTEM) to decipher the nanostructure and layer charge heterogeneity in these minerals. HRTEM results were compared with those obtained from powder X-ray diffraction (XRD) analysis. Samples were either exchanged with Na+ ions followed by equilibration with a very dilute solution of NaCl in a pressure membrane apparatus at 316 hPa (pF = 2.5) to see the effect of hydration and applied pressure on layer organization, or exchanged with dodecylammonium ions to see the expansion behavior. Oriented samples were embedded in a low viscosity resin and cut approximately 500 Å thick perpendicular to d(001) using an ultramicrotome fitted with a diamond knife. In general, Na-saturated soil clays possessed crystallites that were thinner (c-direction) and shorter (ab-direction) as compared with reference clays. In all cases, samples treated with dodecylammonium chloride exhibited nanostructures that were more disintegrated as compared with Na-saturated samples. In a soil vermiculite, dodecylammonium ion exchange showed frayed edges indicating the initiation of mica transformation to vermiculite from edge toward core. In a reference vermiculite (Transvaal) treated with dodecylammonium ions, in addition to completely expanded crystallites, a regular interstratification between expanded vermiculite and mica (phlogopite) layers was clearly observed in some crystallites. Such nanostructural details were not detected by XRD. HRTEM of the Na-treated illite showed thick crystallites having 10 Å layer separations, whereas the dodecylammonium-exchanged illite showed three types of layers with different degrees of expansion indicating charge heterogeneity in illite: 1) unexpanded (10 Å, highest charge) crystallites; 2) expanded high-charge vermiculite-like (24 Å) crystallites; and 3) occasionally expanded high-charge vermiculite-like (24 Å) layers interspersed in the matrix of 10Å crystallites.

In this paper we analyzed by electron microscopy and X-ray diffraction (XRD) the exposed lacustrine clay in a stratigraphic column at Charo Canyon, State of Michoacán, Mexico. Smectite, cris-tobalite, albite and quartz are the main mineral species in the sediments. Smectite is the most abundant and has a nanometric twinned small particle habit. The low crystallinity of the smectite detected in some of the samples seems to be associated with instability of the paleohydrological regime in which clayey material was deposited. Iron from underlying volcanic ash is apparently responsible for the iron concentration detected in the smectite structure.

The structure, chemistry and distribution of hydrothermal alteration and weathering products of feldspars and glass in 3 samples of Yucca Mountain tuffs (GSW G4 borehole at a depth of 1531 ft (464 m) and USW GU3 borehole at 1406 ft (426 m) from the Calico Hills Formation and USW G4 at a depth of 272 ft (82.4 m) from the Topobah Springs Member) were examined by high-resolution transmission electron microscopy (HRTEM) and analytical electron microscopy (AEM). Alteration products are of interest because they may influence the form and distribution of contaminants released from the proposed high-level nuclear waste repository. Samples from the Calico Hills Formation contain alkali-bearing aluminosilicate glass and its alteration products. Zeolites appear to have formed from compositionally similar glass by recrystallization, probably under hydrothermal conditions. Crystals are fibrous and frequently no more than a few tens of nanometers in diameter. Porous aggregates of few-nanometer-diameter, poorly crystalline silica spheres (probably opal C-T) develop adjacent to corroded glass surfaces and zeolite crystals. Finely crystalline Fe-rich smectites coat etched glass surfaces, zeolites and feldspar crystals and occur within opal-like silica aggregates. Microstructures in the clay-dominated coatings and details of smectite-glass interfaces suggest that clays grow in orientations controlled by heterogeneously retreating surfaces and from constituents released at associated glass dissolution sites. The alteration assemblage also includes finely crystalline hematite, goethite, Mn-oxide films and illite formed by alteration of muscovite. The zeolitized sample contains abundant opal-like silica whereas glass in the unzeolitized sample is weathered to smectite-like clays. These differences may be attributed to hydrological and consequent geochemical factors resulting from the higher porosity of zeolitized samples. Exsolved alkali feldspar, which occurs as micron-sized crystals in the Calico Hills Formation and as phenocrysts and in the groundmass of the devitrified Topobah Springs Member, are almost unaltered. Feldspar alteration is confined to cracks and grain boundaries, where minor, poorly crystalline, Fe-bearing aluminosilicate alteration products are developed. In these tuffs, most of the porosity, permeability, high surface area and capacity to affect solution chemistry are associated with products of glass alteration.

The ability of Na-activated bentonite to remove Ni2+ and Co2+ from aqueous solutions at room temperature (22 ± 1°C) was studied under various experimental conditions. The parameters studied were solid-to-liquid ratios and initial cation concentrations. Experiments involved the behavior of bentonite vs. Ni and Co separately and where Ni and Co were present in solution at different concentrations and ratios. Bentonite retained substantial amounts of both metals readily, but it showed a higher affinity for Ni. Over-exchange appears when initial metal concentration exceeds the concentration corresponding to the cation exchange capacity (CEC) of bentonite. The presence of both metals in solution may be either synergistic or antagonistic sorption, depending on the initial ion concentrations.

Analytical electron microscopy was used to confirm the location of pillars of zirconia in pillared montmorillonite. Data show that the pillared clay is of “high” quality, with surface areas ranging from 200 to 250 m2/g and (001) spacings in the 17–18 Å range. The zirconia-rich pillars were observed using bright-field imaging, annular dark-field imaging, and energy-filtered imaging. The composition of the pillars was confirmed by performing nano-analysis using energy-dispersive X-ray spectroscopy and electron energy-loss spectroscopy. The pillars apparently have an irregular shape <50 Å in size. The shape and relatively large size of the pillars suggest that zirconia dispersion is not ideally distributed in this sample. This study is apparently the first report of electron microscopy observation of pillaring material in clays.

—The charge of the expandable interlayers in a series of fourteen diagenetic illite/smectites (I/S) from lower Paleozoic K-bentonites was determined by the alkylammonium ion exchange method. The magnitude (<0.50 equivalents per half formula unit) and characteristic heterogeneous distribution of interlayer charges in eight samples with expandabilities from 70% to about 15% confirm the smectitic character of the expandable interlayers in this range. This result coupled with the lack of a correlation between expandability and interlayer charge is consistent with the hypothesis of a layer-by-layer transformation from a precursor smectite to highly illitic I/S clays during K-bentonite diagenesis. The charge of the expandable interlayers in I/S samples with about 10% or less expandabilities have been inferred to be vermiculitic rather than smectitic. The K-fixed interlayers and expandable interlayers in these samples appear to be similar in charge. The significantly higher charges inferred for the highly illitic samples can be consistent both with a layer-by-layer transformation and the neoformation mechanisms proposed in the literature for the formation of illite.

A saponite pillared with a single (Al2O3) or a mixed (SiO2-TiO2) oxide exhibited basal spacings of 16–19 and 30–40Å, respectively. The pillared structures were found to be stable up to 700°C. Water, nitrogen, and high resolution argon adsorption were used to study the effect of thermal treatments on surface chemistry, pore structure, and surface area of these pillared clays. The pillared saponites exhibited a hydrophobic behavior at temperatures > 500°C, whereas such behavior was observed at ≥300°C for montmorillonite. Most of the micropores in the Al2O3 pillared clays were < 10 Å, whereas the SiO2-TiO2 pillared clays showed a broad distribution of pores in both micropore and mesopore regions. The SiO2-TiO2 pillared samples possessed higher surface area compared with Al2O3 pillared clays. The percent decrease in surface area was smaller for pillared saponites compared with pillared montmorillonites when calcined from 300° to 700°C, indicating a higher thermal stability of the former. The pillared clays were also characterized by solid state 27Al and 29Si magic-angle spinning nuclear magnetic resonance (MAS/NMR) spectroscopy. There was no direct evidence of cross-linking (covalent bonding between the clay layer and pillar) in montmorillonite irrespective of the types of pillars. In saponite, however, a significant structural modification took place. 27Al spectra of Al2O3 pillared saponite heated at ≥300°C appear to indicate an increase in AlVI as a result, at least in part, of initiation of hydrolytic splitting of Si-O-Al bonds. The actual release of Al from the tetrahedral sheet probably occurred at a temperature > 500°C and completed around 700°C with the formation of Si-O-Si linkages. The decreased intensity of peak due to Si(1Al) in 29Si spectra of the sample heated at 700°C corroborates the 27Al MAS/NMR results. Additionally, the 29Si spectra indicated a cross-linking between SiO4 (clay sheet) with Al2O3 pillars, which could be achieved by inverting some silica tetrahedra into the interlayer. 27Al and 29Si spectra of SiO2TiO2 pillared saponite also showed the trend similar to that exhibited by Al2O3 pillared saponite, indicating that the crystal chemistry of the host may be more important than the nature of pillars in the structural modification and cross-linking behavior of thermally treated pillared clays.

An ancient Egyptian limestone sculpture was found to be undergoing major structural decay when stored in a museum environment. Mineralogical and petrographic analysis of the limestone showed a high proportion of clay (≥ 10% by weight) that was concentrated along bedding planes. The clay fraction consisted mostly of sepiolite (>90%) and palygorskite (<10%). Minor quantities (≤l%) of soluble salts (NaCl and NaNO3) were also found. Wetting/drying with distilled water and relative humidity cycling resulted in the same delamination cracking damage as that observed in the museum environment. Thermomechanical analyses (TMA) confirmed that the damage was due to expansion (>4.5%) parallel to bedding planes when the limestone was immersed in water. The expansion due to swelling of the clays was directly observed at high magnification in an environmental scanning electron microscope (ESEM) when wetting/drying cycles were performed. X-ray diffraction (XRD) analysis showed that crystalline swelling of sepiolite occurred. This was determined by a shift of (110) reflection (from 12.07 to 12.20 Å) and a decrease of (060) reflection (4.47 Å, to 4.44 and 4.41 Å), when in contact with ethylene glycol (EG) and dimethyl sulfoxide (DMSO), respectively. Swelling also occurred due to hydration of the clay surfaces and to electrostatic forces between clay particles, which, it was assumed, was promoted by the presence of Na counterions in water solution. Possible treatments for the conservation of these artistic objects are proposed and discussed.

Factors that are potentially important in the pulmonary pathogenesis of asbestos and other mineral particles are: 1) morphology, 2) Fe-content, 3) solubility under intraphagosomal conditions, 4) value and sign of the surface potential of the particle, 5) hydrophobicity or hydrophilicity, 6) capacity to activate phagocytic leukocytes, and 7) duration of exposure to the particles. The order of importance of these factors in causing severe or fatal pulmonary pathogenicity is estimated to be: 1 > 3 > 7 > 6 ≫ 5 > 4 > 2. The order of pathogenicity of the minerals is estimated as: amphibole asbestos: crocidolite, tremolite, amosite > erionite > serpentine asbestos: chrysotile > talc > silica > simple metal oxides. Particle length, duration of exposure to the particles, and pre-treatment of the particles may however enhance the pathogenic potential of any of the lower-ranked particles.

The adsorption-condensation of olefins was studied on 7 adsorbents: 2 commercial clays, a natural clay and its protonated form, γ-alumina and porous and nonporous silicas. These adsorbents were characterized by X-ray diffraction (XRD), chemical analysis, thermogravimetric analysis (TGA), differential thermal analysis (DTA) and determination of specific surface area measurement by the BET method. The experiments were carried out gravimetrically, in gas- or vapor-solid systems, at 25 °C and on adsorbents dried at 120 °C. Adsorption-condensation of olefins are fast processes, diffusion controlled. Alumina and silicas adsorb olefins and paraffins only reversibly, but are unable to condense olefins. The water polarized by the countercations is the source of Brønsted acid sites. When the gas phase is evacuated or swept with inert gas, the condensation terminates. On clays, paraffins are reversibly adsorbed but no condensation was observed.

Synthetic hectorite clay minerals were hydrothermally crystallized with direct incorporation of a series of five water-soluble polyvinyl alcohols (PVA) of molecular weights from 9000-146,000. The molecular weight of PVA had little effect on the success of hydrothermal hectorite synthesis, d-spacing or the amount of polymer incorporated. The basal spacings range from 19.5 Å to 20.8 Å and the amount of polymer incorporated ranges from 20 wt.% to 23 wt.%. Incorporation of PVA within the clay inter-layers, along with Li(I) ions to compensate the lattice charge, is indicated. Thermal gravimetric analysis and small angle neutron scattering were used to further examine the polymer-clay systems. Small PVA-clay crystallites that are coated with excess PVA are indicated. Removal of the polymer does not alter the extended synthetic clay network, and the nitrogen BET surface area increases from <5 m2/g to >200 m2/g.

High resolution transmission electron microscopy (HRTEM) have been performed on dispersed portions of one R > 1 and two R3 illite/smectite (I/S) samples from Silurian K-bentonites. R > 1 sample was studied by HRTEM before and after alkylammonium ion treatment and R3 samples were studied only after alkylammonium ion treatment. The HRTEM images of the chemically untreated R > 1 sample were predominated by lattice fringe contrast with 20–40 Å periods, interpreted to represent various ordered I/S units. HRTEM images of the three alkylammonium-treated samples displayed very small, dispersed particles composed of illite packets separated by alkylammonium expanded interlayers. In the R > 1 sample, illite packets were mostly 20 Å to 40 Å thick whereas in R3 samples they were predominantly over 40 Å. Although a good degree of dispersion of the bulk samples was achieved, dispersed particles recorded on images were thicker than the fundamental particles postulated by Nadeau and coworkers. Alkylammonium ion-expanded interlayer thicknesses point out a trend toward a higher charge in the expandable interlayers (i.e., illite particle surfaces) with increasing illite content from the R > 1 sample to the R3 samples. In the R3 samples, the interlayer charge is sufficiently high to be vermiculitic.

A method is described for the separation of the finest particles from soils and sediments without mechanical disturbance. Particles are separated through the induction of osmotic stress. Generally, samples are treated with a concentrated sodium salt solution and then exposed to water by diffusion. Naturally sodic samples are simply exposed to water. Solid samples and the swollen and dispersed material they produce are confined by dialysis tubing. Examples show that the method gives a size gradient of particles in a vertical column of suspension. The compositions of particles can vary with size. The method can be used to show the effects on separated particles of ions other than Na+ and also of other physicochemical treatments of soils and sediments. It is inexpensive and requires little labor.

The present paper represents an extension of recent work that considered the partitioning response of binary solvents placed into contact with charged, expandable clays. Previous theoretical work yielded a model of partitioning by performing a thermodynamic analysis, involving the work of polarization, on a binary solvent, treated as a continuum and residing within the interlayer space of a layered aluminosilicate clay. Partitioning, or the tendency for sorbed and bulk phases to have different compositions, was shown to be sensitive to the dielectric properties of the 2 solvents of the binary mixture and to the surface charge density on the clay, among other factors. Although previous experimental work has helped to validate the theory, additional work is reported here that looks at hysteresis effects, the role of the exchangeable cation (usually organic), the prediction of adsorption isotherms and the contribution that partitioning, or sorption, makes to the disjoining pressure that develops in binary solvent systems. In this current study, 3 different organo-clays were considered: Cetyltrimethylammonium (CTMA), Isopropanolammonium (IPA), and Benzylammonium (BA) montmorillonite. Solvent systems under study included: acetone/chloroform (a-c), acetone/quadricyclane (a-q) and acetonitrile/chloroform (an-c). While partitioning of the a-c system on CTMA-clay follows theory quite well, theory tends to over-predict partitioning for the a-q system on the same clay and under-predict partitioning for the an-c system on all clays. Predicted adsorption isotherms range from highly nonlinear to nearly linear. Finally, the delamination and subsequent swelling processes of BA-clay in a water/acetonitrile binary solvent system are very sensitive to composition, a result that is directly linked to the partitioning process.

High-resolution transmission electron microscopy (HRTEM) examinations have indicated that three types of surface layers may exist in natural kaolinite crystals. Type 1 has the expected 7-Å surface layer as terminations. Type 2 has one 10-Å pyrophyllite-like (or low-charge beidellite-like) layer as the surface layer on one side of a kaolinite particle (i.e., the layer sequence is TOTOTO … TOTOTOT, where T stands for tetrahedral sheet, O for octahedral sheet). Some industrial-grade highly-ordered kaolinites have such a 10-Å 2:1 surface layer on one side of the crystal. The spacing between the 10-Å layer and the adjacent 7-Å layer is not expandable. Type 3 kaolinite has one or several 10-Å collapsed smectite-like layers at one or both sides of a stack, i.e., (TOT)TOTO … TOTOTOT(TOT), forming a special kind of kaolinite-smectite interstratification. This type has only been recognized in some poorly-ordered kaolinites. The surface smectite layer(s) contribute to higher cation exchange capacity (CEC) values. These 10-Å surface layers were not detectable by X-ray diffraction (XRD). HRTEM and electron diffraction examination also revealed the structural features of individual kaolinite crystals. All kaolinites (from various origins and sources) studied show C-face-centering Of non-hydrogen atoms. Defects within the layer structure are common in both well-ordered kaolinite and poorly-ordered kaolinite.

Montmorillonite (Mnt), belonging to the smectite group and representing a 2:1-type clay mineral with good cation-exchange and swelling capacities, is a common clay component of soils. It was observed that some Mnt preparations exhibit peroxidase-like (P-L) activity using N,N-diethyl-p-phenylenediamine sulfate salt as a substrate. Both native (non-swelling) and swelling Mnt exhibited similar P-L activity. Modification of Mnt with copper and iron influenced both P-L activity and phenol polymerization. Both free and textile-bound Cu-Mnt (Sigma-Aldrich) enabled phenol removal. Soil Mnt P-L activity is probably involved in lignin breakdown and decontamination of soils polluted with phenol-containing molecules.

As the water content is increased, the consistency of a fine-grained soil changes from a semi-solid state to a plastic state and finally to a liquid state. The plastic limit (PL) is the point at which the consistency, caused by the soil water content, is transformed from a semi-solid state to a plastic state. The liquid limit (LL) is the point at which the consistency is transformed from a plastic state to a liquid state. The plastic limit and liquid limit are often collectively referred to as the Atterberg (or consistency) Limits. Although the liquid and plastic limits are easily determined, fundamental interpretations of the limits and quantitative relationships between their values and compositional factors are more complex. Previous studies examined artificially-prepared soil samples that contained monomineralic clays and a non-clay substance(quartz sand). These studies have shown that in soils without expandable clays the PL and LL water contents were mostly related to surface area and clay content. For soils that contain expandable clays, the PL and LL values are also dependent on interlayer water content. Hence, expandable clay mineral contents are needed to calculate PL and LL values. These relationships have been presented in a general analytical form. The aim of these investigations was to identify practical applications. Mineral compositions and surface areas of five randomly selected natural soil samples were used to estimate PL and LL values. The estimated values were compared to experimentally measured liquid limits (by the ‘fall-cone’ test) and plastic limit (by the ‘rolling thread’ test) values. The measured PL values ranged from 18.77 to 44.92% and the LL values from 31.19 to 82.10%. The differences between estimated and measured Atterberg Limits were 3.0–7.1% for thePL and 2.7–7.8% for the LL. Minor differences in measured and estimated Atterberg Limits were probably due to soil organic matter (1.2–2.7%).

One montmorillonite, STx-1 (Texas, USA), was activated with different amounts of Al and tetramethylammonium (TMA+) cations to obtain materials with a combined Al3+ and TMA+ content equal to its cation exchange capacity. The adsorption capacity of these samples was studied saturating them with hept-1-ene at room temperature. The samples were heated and the evolved gases analyzed by Fourier transform infrared spectroscopy and gas chromatography-mass spectrometry. Hept-1-ene reacted with the clays via proton transfer and resulted in the formation of a variety of reaction products (>60 hydrocarbons). In general, the presence of TMA+ cations significantly reduced the population of protons to selectively produce isomerization and hydration products.