This article describes the design and evaluation of a new type of propulsion mechanism that uses modular umbrella-like wings oscillating symmetrically in counterphase to generate thrust. The principle of the propulsion and movement of the modular umbrella-like wings was first developed, and the mechanism used to implement the movement of the modular wings was subsequently designed. A structural model and the assembly relationship of the propulsion mechanism were developed for prototype fabrication. An experiment was established to measure the kinematic and mechanical performances of the propulsion mechanism for different reciprocating frequencies and travels. The results for the single umbrella-like wing indicate that either increasing the frequency or enlarging the travel can enhance the average aerodynamic force generated by the wing in one cycle. The results for the modular umbrella-like wings demonstrate that the inertial force generated by the mechanism can be balanced using a symmetrical structure. The average aerodynamic force would be markedly enhanced by increasing the percentage of the time that the outspread wing is moving downwards; e.g. the average aerodynamic force generated by the modular umbrella-like wings was increased by 85.84% compared to the value for a single umbrella-like wing for the same travel and frequency. This work provides practical guidance for optimising the structure design.

This paper proposes an adaptive guidance law for attacking a ground target based on motion camouflage strategy. The coefficients of normal and bi-normal feedback guidance law are given according to the relative motion relationship under Frenet frame. Utilizing the coefficients, the motion camouflage proportional guidance law is derived. In order to improve the initial overload characteristic of the missile, an adaptive feedback coefficient is introduced. Then, the adaptive guidance law is applied to a longitudinal plane interception problem with impact-angle constraint. Finally, the validity of this guidance law for air-to-ground missiles is proved by simulations.

The development of new technologies – such as rapid prototyping – and the use of materials with improved properties – such as highly resistant extruded polystyrene foam which can be easily and precisely shaped, while conserving its mechanical properties – allow researchers to improve design concepts. This article details the development of a new set of morphing wings for a 15-kg maximum take-off weight Unmanned Aerial Vehicle (UAV) from concept design, to flight tests, including modelling, design optimisation, construction and wind-tunnel tests. A set of comparator-equivalent conventional wings have been used throughout in order to be able to judge any benefits stemming from the adoption of morphing technology. This article shows that the morphing wings provide a controllable aircraft while reducing drag by a factor of 40% compared to the comparator wings with conventional ailerons in a deflected position.

Icing in conditions where clouds contain both liquid and solid phase particles has attracted considerable interest in recent years due to numerous in-flight incidents including engine rollbacks in the vicinity of deep convective clouds in tropical regions. These incidents have prompted certification authorities to investigate and extend the icing conditions to include solid and mixed-phase clouds for airworthiness certification. These efforts have resulted in the amendments issued by the Federal Aviation Administration (FAA) and European Aviation Safety Agency (EASA) to the certification specifications of large aircraft, FAR-25 and CS-25, respectively. Flight tests, laboratory tests and computer simulations are among the acceptable means to show compliance with these specifications. Considerable effort has been spent worldwide in order to develop icing simulation software for liquid phase clouds in the past four decades, but until recently, most of these software did not have the capability for solid- or mixed-phase clouds. One of the aims of the High Altitude Ice Crystals (HAIC) project funded by the European Commission within Framework Program 7 is to address this shortcoming. The present study combines the models related to solid- and mixed-phase icing that is developed within HAIC with an in-house numerical tool. The tool has four modules; a flow-field solution module that uses the Hess-Smith panel method, a module for computing droplet and ice crystal trajectories and collection efficiencies using the Lagrangian approach, a thermodynamic module, and an ice accretion module that utilises the Extended Messinger Model. The numerical tool is tested against experimental test cases including liquid and mixed-phase conditions for various aerofoil and axisymmetric intake geometries. The agreement of the obtained results with experimental data is encouraging.

One of the key problems in the development of morphing aircraft is the morphing structure, which should be able to carry loads and change its geometry simultaneously. This paper investigates a compliant structure, which has the potential to change the dihedral angle of morphing wing-tip devices. The compliant structure is able to induce deformation by unsymmetrical stiffness allocation and carry aerodynamic loads if the total stiffness of the structure is sufficient.

The concept has been introduced by building a simplified model of the structure and deriving the analytical equations. However, a properly designed stiffness asymmetry, which is optimised, can help to achieve the same deformation with a reduced actuation force.

In this paper, round corrugated panels are used in the compliant structure and the stiffness asymmetry is introduced by changing the geometry of the corrugation panel. A new equivalent model of the round corrugated panel is developed, which takes the axial and bending coupling of the corrugated panel into account. The stiffness matrix of the corrugated panel is obtained using the equivalent model, and then the deflections of the compliant structure can be calculated. The results are compared to those from detailed finite element models built in the commercial software Abaqus. Samples with different geometries were manufactured for experimental tests.

After verifying the equivalent model, optimisation is performed to find the optimum geometries of the compliant structures. The actuation force of a single compliant structure is first optimised, and then the optimisation is performed for a compliant structure consisting of multiple units. A case study is used to show the performance improvement obtained.

Thermal-mechanical design is a time-consuming process even at its preliminary design stage. This is due to the large number of components and boundary condition data, the complexity of the geometry, and the iterative nature of the design process. The conventional design process separates the geometric and physical models and results in considerable human interventions during the design process. By assigning the breakpoints to engine assembly features as internal parameters, this article reports a novel feature-based design approach where the associated boundary conditions are represented parametrically along the feature geometric contours. They are updated automatically as per the geometrical changes, including topological changes, and hence bridging the gap between the geometric and physical models. The current approach enables data re-use of both the geometries and physical information from previous engine designs to generate new designs, dispensing with the excessive human interventions. Although the methodology is generic and applicable to other design scenarios, its capability is demonstrated in this article by some representative challenging industrial applications, sitting in the 2D preliminary gas-turbine design domain. The test cases show that the method can significantly reduce the time-cost of the iterative thermal-mechanical design flow.

Virtual engineering tools are not currently employed extensively during the certification and commissioning of flight simulator motion systems. Subjective opinion is regarded as sufficient for most applications, as it provides verification that the motion platform does not cause false cueing. However, the results of this practice are systems that may be far from optimal for their specific purpose. This paper presents a new method for tuning motion systems objectively using a novel tuning process and tools which can be applied throughout the simulators life-cycle. The use of the tuning method is shown for a number of simulated test cases.