This paper assesses the financial performance of 35 European airports for the decade 1990 to 2000, comparing those subject to partial or full privatisation with those still in public ownership. In contrast to earlier research, the outcomes of partial factor productivity (PFP), financial ratio (FRA) and data envelopment analysis (DEA) are evaluated, in order to investigate differences attributable to the degree of privatisation. Changes in performance after a change in ownership structure are reviewed. The analysis of sample data reveals economically meaningful and statistically significant differences between publicly owned and privatised airports. The major differences lie in operating efficiency, capital productivity and capital structure. Although partially and fully privatised airports operate more efficiently, this does not translate into significantly higher returns on shareholders’ funds. Due to their at least indirectly government-backed credit standing, publicly owned airport companies can assume more debt relative to their respective equity. This results in considerably higher gearing and financial leverage, which compensates for the comparatively low return rate on assets.

The results of an investigation into the effects that sub-boundary layer vortex generators (SBVGs) have on reducing normal shock-induced turbulent boundary-layer separation are presented. The freestream Mach number and Reynolds number were M = 1·45 and 15·9 × 106/m, respectively. Total pressure profiles, static pressure distributions, surface total pressure distributions, oil flow visualisation and Schlieren photographs were used in the results analysis. The effects of SBVG height, lateral spacing and location upstream of the shock were investigated. A novel curved shape SBVG was also evaluated and comparisons against the conventional flat vane type were made. The results show that in all but two cases, separation was completely eliminated. As expected, the largest SBVGs with height, h = 55%δ, provided the greatest pressure recovery and maximum mixing. However, the shock pressure rise was highest for this case. The experiments showed that the mid height SBVG array with the largest spacing provided similar results to the SBVG array with the largest height. Reducing the distance to shock to 10δ upstream also showed some improvement over the SBVG position of 18δ upstream. It was suggested that total elimination of the separated region may not be required to achieve a balance of improved static pressure recovery whilst minimising the pressure rise through the shock. The effect of curving the SBVGs provided an improved near wall mixing with an improved static and surface total pressure recovery downstream of the separation line. The optimum SBVG for the current flow conditions was found to be the curved vanes of h = 40%δ, with the largest spacing, located at 18δ upstream of the shock. Overall, it was apparent from the results that in comparison to larger vortex generators with a height comparable to δ, for SBVGs the parameters involved become more important in order to obtain the highest degree of mixing from a given SBVG configuration.

Some in-service deterioration in any mechanical device, such as an aero-engine, is inevitable. As a result of experiencing a deterioration of efficiency and/or mass flow, an aero-engine will automatically adjust to a different set of operating characteristics; thereby frequently resulting in changes of rpm and/or turbine entry temperature in order to provide the same thrust. Rises in the turbine entry-temperatures and the high-pressure turbine’s rotational speed result in greater rates of creep and fatigue damage being incurred by the hot-end components and thereby higher engine’s life cycle costs. Possessing a better knowledge of the effects of engine deterioration upon the aircraft’s performance, as well as fuel and life usages, helps the users to take wiser management decisions and hence achieve improved engine utilisation. For a military aircraft, using a computer performance simulation, the consequences of low-pressure (LP) compressor’s deterioration upon an aero-engine high-pressure (HP) turbine blade’s life-consumption have been predicted.

The exits which passengers select in evacuation situations and the exits which are available post-crash is of great interest to aviation safety regulators who make rulings defining exit separation and aircraft evacuation certification, aircraft designers who develop the interior layout of aircraft cabins and position exits within the fuselage, cabin safety specialists who develop procedures for managing aircraft evacuation and cabin crew who must control aircraft evacuations. In this paper we examine issues associated with passenger exit selection behaviour and exit configurations frequently experienced during survivable crashes. This work makes use of the latest version of the Aircraft Accident Statistics and Knowledge database AASK V4.0, which contains information from 105 survivable crashes and over 2,000 survivors.

In the present investigation, a potential flow model based on panel method has been developed for calculation of two dimensional separated flows past square and rectangular cylinders. Free vortex lines are assumed to emanate from the points of separation that converge downstream of the body. The converged wake shape is iteratively obtained by integrating the velocity vectors at the collocation points. For solving separated flow past square and rectangular cylinders, four different versions of the solver have been developed for a wide range of incidence, namely, for zero, low, moderate and high angles of incidence. For validation of computed results, experimental investigations have been carried out in a low speed wind tunnel to obtain the surface pressure distribution on square cylinder and rectangular cylinder over a range of angles of incidence. Comparison is reasonably good.

The recent decline in the USA aerospace industry has resulted in fewer programs, fewer engineers, and a potential loss of capability for future technology development. As engineers retire or leave the industry, their corporate memory or retained knowledge must be preserved for future use. A process to capture their expert knowledge is described, and a framework which provides a means to retrieve and use this valuable technical information is shown. Four examples of integrated design and analysis systems for four diverse technologies and applications are discussed.