In this paper, we propose a double balanced mixer with a tunable Marchand balun. The circuit is designed in a SiGe BiCMOS process using Schottky diodes. The tunability of the Marchand balun is used to enhance critical parameters for double balanced mixers. The local oscillator-IF isolation can be changed from –51 to –60.5 dB by tuning. Similarly, the IIP2 can be improved from 41.3 to 48.7 dBm at 11 GHz, while the input referred 1-dB compression point is kept constant at 8 dBm. The tuning have no influence on conversion loss, which remains at 8.8 dB at a LO power level of 11 dBm at the center frequency of 11 GHz. The mixer has a 3 dB bandwidth from 8 to 13 GHz, covering the entire X-band. The full mixer has a size of 2050 μm × 1000 μm.

In this paper, a 2.45-GHz wideband harmonic rejection rectenna for wireless power transfer is proposed. The rectenna comprises a microstrip-fed circular ring slot antenna (CRSA) and a series-parallel rectifier (SPR). A compact micro strip resonant cell is inserted into the CRSA so that the harmonic suppression over a wide bandwidth (3–8 GHz) can be obtained. The radio-frequency (RF)–DC conversion efficiency of the SPR is improved effectively by loading a proper compensating inductance, especially under the low input power levels. Furthermore, the proposed rectenna can easily achieve large-scale rectenna arrays using its simple structure. The adopted rectenna fabricated on a low cost Taconic RF-35 substrate has been measured. By up to 3rd-order harmonic rejection, the efficiency of the rectenna can achieve 70.2% with the optimum load resistance 1 kΩ. Good agreement among the calculated, simulated, and measured rectenna is observed.

Voltage doubler rectifiers are usually applied to systems with high voltage and low current requirement. An X band voltage doubler rectifier has been developed with 72% conversion efficiency. To the best of our knowledge, the obtained rectifying efficiency is the maximum reported to date at X band with Schottky diodes. The working characteristics of the diodes in the voltage doubler rectifier are analyzed in detail. Closed-form equations of diode input impedance and rectifying efficiency are presented and validated using Advanced Design System simulations. The matching network design of the proposed rectifier is based on the closed-form equations. The preliminary rectifying efficiency is predicted by the closed-form equations as well. Measured and simulated results are in good agreement.

Design method for band-stop filters (BSFs) that suppress a requested number of spurious bandstops and reduce ripples in the passbands below ~1 dB is proposed. BSF is designed in a form of a cascade of cells, each consisting of steps of equal electrical length, where the number of steps is used to control the number of suppressed spurious bandstops. Analytical formulas are developed that enable initial design of BSF for a given central frequency, depth, and bandwidth of the stopband. Varying the minimum characteristic impedances of initial cells, through an optimization using circuit simulation, the ripples in passbands are reduced below ~1 dB. Using the proposed theory, three filters in microstrip technology, with suppression of 3, 5, and 7 spurious stopbands respectively, were designed, fabricated, and measured. Good agreement between simulated and measured results has been observed. The proposed design can be recommended for filters having broad stop bandwidths, between 40 and 100%.

A novel miniaturized dual-mode bandpass filter (BPF) using hexagonal loop resonator is presented. In order to reduce the circuit size, capacitive loading structure is applied to enhance the self-capacitance and electrical length of the hexagonal loop resonator. The frequency selectivity and out-of-band rejection of the proposed BPF can be improved by the two inherent transmission zeros in each side of the passband. Compared with the conventional hexagonal loop resonator without capacitive loading structure, the size of the proposed resonator is reduced by 46.6%. The simulated and measured results are presented and show good agreement.

In this paper, an ultra-wideband (UWB) filter with a notch band using T-shaped step impedance resonator loaded with cross-shaped open stubs has been presented. The notch band is formed by utilizing intrinsic zero. The characteristics of the new quad-mode resonator have been analyzed using odd-even mode analysis method. It can be shown that it is the intrinsic zero that generates the notch band. In addition, wide tunable notch band form 5–9.3 GHz can be achieved. A UWB filter with a notch band centered at 6.25 GHz using the proposed quad-mode resonator has been designed, fabricated, and tested. Experiment results show that the attenuation in notch frequency is >22 dB while the return loss of the simulation and measurement results are 22 dB/20 dB and 14.5 dB/11.2 dB in the lower and upper passband, respectively, which illustrate that the simulation and measurement results are in agreement.

A novel small-size filtering power divider (PD) featured four-function integration is proposed. These four integrated functions are high-selectivity filtering, inherent DC block, high all-frequency isolation, and high-power applications. Using single-layer planar circuit technology, this proposed PD can be implemented easily. The measured results of a prototype show that it can operate at 2 GHz with a −10 dB matching bandwidth of 6% and all-frequency −15 dB isolation.

In this paper, a novel compact microstrip low-pass filter (LPF) with ultra wide stop band and sharp roll off, is proposed. In the proposed structure, a high impedance transmission line is loaded by compact microstrip resonant cells, which results in ultra wide stopband. The −3 dB cut-off frequency of filter is 1.5 GHz and the maximum insertion loss is <0.1 dB in the passband. The proposed LPF presents extremely wide stopband from 1.68 to 44 GHz, with more than the −20 dB attenuation level, which suppresses the 2nd to 29th harmonics with high rejection levels. The size of the proposed LPF is only 0.1 λg × 0.19 λg, which shows excellent size reduction. There is a good agreement between the simulated and measured results.

Synthesis of differential-mode bandpass filter (BPF) with good common-mode suppression has been described and demonstrated on the basis of ring dielectric resonator (RDR) for high-performance communication system. A RDR with two pairs of feeding lines has been used to excite TE01δ-mode. This unique combination of feeding lines and the ring resonator creates a differential passband. Meanwhile, TM01δ-mode of the DR can also be excited to achieve common-mode rejection in the stopband. Transmission zeros are created in the lower and upper stopband to further improve the selectivity of the proposed BPF. A second-order differential BPF is designed, fabricated and its performance is measured to validate the concept. There is good agreement between simulated and measured results.

An ultra-wideband (UWB) highly compact bandpass filter with extremely high passband bandwidth is presented. The proposed structure is made using three-staged stepped-impedance lines and a composite right/left-handed transmission line (CRLH-TL) synthesized with meander fractal like ring slot in the ground and series capacitive gap in conductor strip. The capacitive gap in conductor strip and meander fractal like ring slot in the ground plane play major role for controlling the lower and higher cut-off frequencies. The equivalent circuit model of proposed filter is demonstrated and lumped parameters are extracted. A prototype is fabricated to experimentally validate the performance of proposed filter. The proposed UWB filter has extremely wide −10 dB return loss passband bandwidth from 3.14 to 18.26 GHz with relative bandwidth of 142% and insertion loss better than 0.5 dB. Also it achieves a wide upper-stopband from 19.7 to 24.4 GHz with insertion loss better than 13.0 dB, return loss <1.5 dB and sharpened rejection skirts outside the passband at both lower and upper frequency ends. Good agreement is found between simulated and measured results with measured group delay variation in the passband <0.65 ns.

Specifications of the substrates are among the most important and problematic parameters that still do not have proper models in the design procedures of metasurfaces. In this paper, a new fast and exact algorithm based on artificial neural networks (ANNs) is presented, which makes it possible to design frequency-selective surfaces (FSSs) on various kinds of standard substrates. Also for the first time, designing FSSs on uniaxial anisotropic substrates can be easily done in short time and without any optimization algorithms. During this paper, first equivalent geometry approach (EGA) is demonstrated as a new method of preparation the ANNs. Then EGA is used to train geometry transformation ANNs. The advantage of this approach is to reduce the size of training datasets by about 98% and prevent from superfluous simulations. Hence, the time needed for training of the networks is much less than before. Numerical results are used to show that the required time for developing FSSs is <200 ms on average, and errors are <2%. For the final validation, a prototype sample of FSS is fabricated on the RO4003 substrate with 20 mil thickness. Both analytical and experimental results confirm the correctness of the predicted values.

Electromagnetic characteristics of the E-plane T-junction for two rectangular waveguides using resonant coupling between the waveguide sections were studied by mathematical modeling. The problem of coupling between infinite and semi-infinite rectangular waveguides through a resonant slot in the end-wall of the semi-infinite waveguide in the presence of resonant monopole is solved in a strict electrodynamic formulation. The monopole with variable surface impedance is placed parallel to the narrow walls at an arbitrary position inside the infinite waveguide. The problem is solved analytically by the generalized method of induced electro-magneto-motive forces. Impedance vibrator inclusions with variable electro-physical parameters have been analyzed as control elements for waveguide junctions. To this purpose energy characteristics of the junction in the single-mode regime of the both waveguides, and also in multi-mode regime of the semi-infinite waveguide is investigated. The results may be useful for development of variety antennas and waveguide devices, which involves waveguide junctions.

In order to counter active jamming, an adaptive polarization cancellation method based on dual-polarization radar is proposed in the paper. First, respectively being obtained by vertical and horizontal polarization channels of dual-polarization radar, the signals from the real target and active jamming are analyzed in composition and characteristic. Then, the weight coefficient is timely derived in practical scene to adjust difference of amplitude and phase of active jamming signals respectively acquired by the two orthogonal polarization channels, so the method can completely eliminate active jamming, but just a little power change for the real target signal. Furthermore, a compensating method for the target signal is developed to improve the angle measuring accuracy of monopulse radars. And the influence factors of adaptive polarization cancellation are analyzed in detail by simulation. Finally, the experimental results prove that it is very effective on both active blanket jamming and active deception jamming.

In this paper, an X-shaped fractal antenna with defected ground structure (DGS) is presented for multiband and wideband applications. The X shape is used due to its simple design and DGS is utilized to achieve size reduction with multiband and wideband features in the frequency range of 1–7 GHz. The proposed structure is fabricated on FR4 substrate with 1.6 mm thickness. We have proposed two different antennas both are having X-shaped fractal patch with a slotted ground plane to have more impedance bandwidth and better return loss. Various parameters like scale factor, width of ground plane, number of slots with their dimensions and feed line length are optimized to have size reduction and for enhancing the performance of antenna. Reflection coefficient shows the multiband and wideband features of proposed antenna. One of the proposed antennas covers various applications like IEEE802.11y at 3.65 and 4.9 GHz, IEEE 802.11a at 5.4 GHz, 802.11P at 5.9 GHz. Other antenna covers applications like IEEE802.16 at 3.5 GHz; 5 cm band for amateur radio and satellite and future 5 G communication systems over 6 GHz. The antenna designing was done using CST software and simulation results were compared with experimental results (using E5071C network analyzer).

This paper presents application of split ring resonators (SRR) in conventional waveguide slot array antenna to achieve performance improvement and multiband characteristics. Three SRRs have been placed on the transverse plane of a conventional slotted waveguide and has been simulated and measured. The measured results show that the antenna has dual band response with respective 10 dB return loss bandwidth 8.23–9.23 GHz (11.45%) and 9.68–11.01 GHz (12.87%). The measured gain and radiation pattern reveal that the proposed antenna has higher gain and front to back radiation ratio as compared with a conventional slotted waveguide antenna. Equivalent circuit of the proposed antenna also has been presented.

An analysis about the effects of various bi-isotropic (BI) coatings and BI background media upon the gain characteristics of an axially slotted cylinder using numerical simulations is presented. It is investigated that chirality and Tellegen parameters of a coating and a background medium play a significant role in modifying the gain properties. It is further studied that an axially slotted cylinder when coated with a strong BI material and embedded in a free space background significantly enhances the gain in the forward direction. On the other hand, a strong Tellegen coating guides most of the radiated field from an axial slot toward rear side of the cylinder.

Dielectric stepped-index flat lens antennas for operation at 12 GHz are presented. A brick-shaped dielectric with a permittivity profile optimized for focusing is sandwiched between the metallic plates of an open-ended parallel-plate waveguide. A tapered slot antenna is placed at the focal point of the dielectric lens, thereby creating antennas with high directivity of 16.8 and 15.8 dBi, respectively. In the two versions of the antenna, the parallel-plate waveguide operates in TEM-mode and in the first higher-order TE-mode, respectively. The dielectric profile is realized by appropriate mixtures of alumina ceramic powder and microscopic hollow glass spheres, realizing permittivity ranging from εrel = 1.31 to εrel = 3.24. The design of the complete antennas is based on geometrical optics followed by optimizations with a full-wave electromagnetic solver. Measurements show good agreement with simulations.

In this paper a new design of compact single layered triangular slotted microstrip patch antenna with spur lines and strip loading is proposed. It has been experimentally investigated that strip loading causes more size reduction where spur lines and triangular slot introduces multi frequency operation of microstrip patch antenna. The size reduction has been found to be 87% for the proposed antenna. In this article the effect of strip loading and spur lines over compactness are individually analyzed.

In this paper, an asymmetric coplanar strip (ACS)-fed quad-band monopole antenna for the global positioning system (GPS), wireless local area network (WLAN), and worldwide interoperability for microwave access (WiMAX) applications is proposed. It is composed of an F-shaped monopole and a partial ground plane, which are both printed on one side of a low-cost FR4 substrate with a compact volume of 40 × 20 × 1.6 mm3. By cutting an open-ended Γ-shaped slot into the F-shaped monopole, four distinct resonant modes are successfully generated. The design process, especially the geometrical configuration of the critical Γ-shaped slot is studied in detail. The proposed antenna has been fabricated and experimental results show that the −10 dB impedance bandwidth can fully cover the 1.575-GHz GPS (1.57–1.59 GHz), 2.4/5.2/5.8-GHz WLAN (2.4–2.485, 5.15–5.35, and 5.725–5.825 GHz), and 2.5/3.5/5.5-GHz WiMAX (2.50–2.69, 3.30–3.70, and 5.25–5.85 GHz) applications with nearly omni-directional radiation patterns and satisfactory gains.

In this paper, compact single-feed dual-band antennas for different wireless applications are proposed. First, a dual-band antenna with a comparatively large frequency ratio of 2.58 is designed. Then, a novel dual-band antenna is introduced in order to enhance the upper frequency band. The technique consists of modifying the feed line structure, which leads to a 9.23% of impedance bandwidth at the central frequency of 6.5 GHz instead of 2.06%. The designed antennas are fabricated and tested in the laboratory and in a small anechoic chamber in order to measure their reflection coefficient, gains, and efficiencies. Good agreement between simulated and measured results is obtained. The designed antennas are particular because they have low profile, very simple single-feed technique, can be designed for large frequency ratios, and also the bandwidth can be clearly enhanced. Therefore, they can be used for different wireless applications.