A new model is proposed on how to account for the inertia of scatterers in radar-based turbulence intensity retrieval techniques. Rain drop inertial parameters are derived from fundamental physical laws, which are gravity, the buoyancy force, and the drag force. The inertial distance is introduced, which is a typical distance at which a particle obtains the same wind velocity as its surroundings throughout its trajectory. For the measurement of turbulence intensity, either the Doppler spectral width or the variance of Doppler mean velocities is used. The relative scales of the inertial distance and the radar resolution volume determine whether the variance of velocities is increased or decreased for the same turbulence intensity. A decrease can be attributed to the effect that inertial particles are less responsive to the variations of wind velocities. An increase can be attributed to inertial particles that have wind velocities corresponding to an average of wind velocities over their backward trajectories, which extend outside the radar resolution volume. Simulations are done for the calculation of measured radar velocity variance, given a 3-D homogeneous isotropic turbulence field, which provides valuable insight in the correct tuning of parameters for the new model.

This paper presents the design, implementation, and validation tests of a C-band analog-front-end (AFE) for the frequency modulated continuous wave (FMCW) radar. The system was designed to be used in various radar applications, including short rage mode, synthetic aperture radar (SAR) and moving target indication (MTI) mode. The AFE presented here was based on commercial off-the-shelf radio frequency components, and designed as a homodyne system, so the final applications were based on the FMCW radar. Validation tests and experiments were carried out in the laboratory and in open-air environments. The authors present tests of the AFE, including MTI and SAR trials, conducted using a ground moving platform (a car) and an airborne platform (a small aircraft). The results are discussed with the prospect of future work and further improvements in mind.

Through-the-Wall Imaging is an ever-expanding area in which processing time, scanning time, vertical, and horizontal resolutions have been tried to improve. In this study, several methods are investigated to obtain efficient reconstruction of through-the-wall imaging radar signals with high resolution. Microwave radar signals, which are produced in YTU Microwave Laboratory, are processed by compressive sensing (CS). B and C scanned reflection data samples collected between 1 and 7 GHz frequency band are taken randomly at 1/4, 1/2 of whole amount and reconstructed by CS method. Considering the signal structure, 10 and 20 compressible Fourier coefficients are taken through CS to analyze the difference between them. In addition, we applied synthetic aperture radar (SAR) processing, also combined with SAR-Multiple Signal Classification over raw data. Experimental performance results are given and shown in the figures with high quality.

Continuous wave radars usually use separate transmit and receive antennas that are close to each other. In such a configuration, the antenna crosstalk is the strongest echo acquired by the radar surveillance channel. Sidelobes of the strongest echo are spread over all range cells, limiting the dynamic range of the radar. In this paper, a mismatched filter approach is presented that substitutes classic correlation in order to suppress correlation sidelobes. Both simulations and measurements are presented.

The backscatter from radar object carries Doppler information of scatterers on the object determined by the radial velocity of scattering points and the radar transmitted frequency. For a rotating object this information is contained in the frequency characteristics over varying aspect angle. Frequency characteristics are used to create projections for Doppler radar tomographic imaging. This paper presents a method for high resolution imaging of a rotating target using a time-frequency transform of a returned signal as tomographic projections. The resolution of a tomographic image depends not only on radar system parameters but also depends on the resolution of input projections. The reassigned spectrogram is proposed for building of tomographic projections, due to its possibility of squeezing of frequency spread. The reassigned spectrogram is sensitive to noise so the denoising procedure in the time-frequency domain must be performed before the reassignment procedure. The denoising is performed by removing Short Time Fourier Transform (STFT) noise coefficients below the appropriate threshold. The STFT is a linear time-frequency transform and coefficients, which belong to the signal and coefficients which belong to noise can be analyzed separately. The efficiency of the proposed idea of imaging is supported by results of numerical experiments.

High-resolution imaging with an airborne synthetic aperture radar (SAR) calls for precise trajectory measurements that can hardly be achieved with common navigation systems. In this paper, an efficient method called the local-quadratic map-drift autofocus is developed for the estimation of residual (uncompensated) motion errors directly from the received radar data. The map-drift autofocus is applied locally on short time intervals to estimate the cross-track components of the aircraft acceleration. The estimated acceleration is then integrated to evaluate the residual trajectory errors on the whole data frame interval. The method has been successfully tested with an X-band airborne SAR system.

This paper addresses the study of the variation effects of incident plane wave on a multiconductor transmission line (MTL), using a coupling circuit model of MTL line with plane wave based on the method of characteristics (Branin method). This model is valid in the time and frequency domains. It has also an advantage of not presupposing the conditions of the charges applied to its ends, which allows it to be easily inserted in circuit simulators, such as SPICE, SABER, and ESACAP. We confirm the validity of this model by comparing our simulation results under ESACAP with other results, and we discuss the variation effects of the incident plane wave on an MTL line.

In this paper, a simple synthesis technique to obtain the geometrical parameters of the modified circular ring for angular and polarizations (perpendicular and parallel) stable frequency selective surface (FSS) has been discussed. The geometrical parameters of the modified circular ring FSS structure have been achieved using the proposed synthesis technique, which is based on the equivalent circuit (EC) approach. In addition to this, the numerical analysis is also discussed to determine the values of EC parameters, which depends on the basic system level characteristics such as frequency of operation and reflection/transmission coefficients. The analytical results are supported using the full-wave three-dimensional electromagnetic (EM) simulators such as CST Microwave Studio and Ansoft HFSS. The sensitivity of the structure to the perpendicular and parallel polarized EM wave up to 50° angle-of-incidences (AOIs) has been discussed. The stability over different AOI is attributed to the appropriate thickness of the structure with its small unit-cell dimensions. We have also fabricated and experimentally tested the proposed FSS structure.

This work focuses on the circuit modeling and full-wave analysis behavior of circular split ring resonator (SRR). We investigate an equivalent circuit model that allows calculating the resonant frequency from the geometric parameters. Equivalent LC parameters of inductance and capacitance are derived using conformal mapping and constitutive equations. Lumped element equivalent circuit models of resonator are investigated highlighting the behavior of inductance and capacitance. In order to validate our proposed analytical LC model, a comparison of theoretical and simulation results has been performed and a good agreement is achieved with a maximum error of 4.23% and a minimum error of 0.52%, which supports the validity of the equivalent model.

This is the first report on novel mushroom-type electromagnetic band gap (EBG) structures, consisting of fractal periodic elements, used for enhancing the gain of microstrip patch antennas. Using CST Microwave studio the performance of rectangular patch antenna has been examined on proposed fractal EBG substrates. It is found that fractal EBGs are more effective in suppressing surface wave thus resulting in higher gain. The gain of rectangular patch has been improved from 6.88 to 10.67 dBi. The proposed fractal EBG will open new avenues for the design and development of variety of high-frequency components and devices with enhanced performance.

A new circularly polarized planar array antenna using linearly polarized microstrip patches is designed and optimized for X-band wireless communication applications. Four square patch elements with feed network are used to design the circularly polarized array antenna. The feed network consists of microstrip lines on the obverse side of the dielectric substrate and slot line on the reverse side of the substrate. Both-sided MIC technology is successfully employed to apply its inherent advantages in the design process of the array structure. The unequal feed line is used to create 90° phase difference between the linearly polarized patches. Therefore, the circular polarization is realized by the combination of linearly polarized patches and unequal feed line. Characteristics of the proposed array are investigated by using two electromagnetic (EM) simulators: advanced design system and EMPro. The −10 dB impedance bandwidth of the antenna is around 5%. The 3 dB axial ratio bandwidth of 1.48% is obtained. The design of the proposed antenna along with parametric study is presented and discussed.

In this paper, a dual wideband microstrip antenna (MSA) has been presented for wireless local area networks (WLAN), worldwide interoperability for microwave access (Wi MaX) and U-NII band applications. The antenna is designed and simulated using CSTMWS V'10. The main goal of this paper is to get multi-frequency behavior by cutting resonant slots into the patch of the antenna and a wideband antenna behavior using an aperture coupled feeding method. The designed antenna has a semi-spiral G-shaped compact structure and an electromagnetically coupled feeding mechanism (aperture-coupled feeding). It is fabricated on an FR4 substrate with a dielectric constant of 4.4 and a dielectric loss tangent of 0.009. The testing of prototype antenna (to measure S11) is done using a vector network analyzer. The measured results are 80% matching to the simulated ones. The parametric study, simulation results, measured results, and applications of the MSA for WLAN, WiMAX, and the FCC unlicensed 5.2 GHz National Information Infrastructure (U-NII) bands are presented in the paper. The antenna shows a simulated gain of about 4.5 dB at the three wireless application bands.

Asymmetric slits loaded irregular shaped microstrip patch antenna with three different ground structures is proposed. All three antennas show triple band characteristics. First antenna with regular ground plane resonates at 1.95, 2.4, and 4.90 GHz with good radiation characteristics and shows right-hand circular polarization at 1.95 GHz. 18.75% of compactness is achieved with triple band characteristics. Further, same patch is used with different defected ground structures. Second antenna resonates at 1.85, 2.4, and 4.85 GHz with suppressed cross-polarization level and antenna shows right-hand circular polarization at 1.85 and 4.85 GHz. Compactness is further improved to the value of 22.91%. The third antenna resonates at 1.95, 2.4, and 4.85 GHz with better gain and radiation characteristics and antenna shows right-hand circular polarization at 1.95 and 2.4 GHz. The small frequency ratio f2/f1 is achieved and the value of f2/f1 is 1.29 and 1.23 for second and third configuration, respectively. Proposed structures show right-hand circularly polarized with suppressed left-hand circularly polarized radiations and suitable for fixed mobile wireless communication applications. All structures are analyzed using Ansoft HFSS v.14 based on finite element method and measured results satisfy the simulated results.

A broadband circularly polarized (CP) beam-steering antenna array is presented. CP antenna is composed of four identical CP slot elements with 2 × 2 configuration and a 4 × 4 feeding network. CP slot element is utilized in array form to improve impedance bandwidth and sequentially rotation method is used to increase axial-ratio bandwidth. Moreover, uni-planer compact electromagnetic band-gap structure is applied to enhance the overall performance of antenna array. Measured results depict that the array has impedance bandwidth over a frequency range of 4.1–7 GHz (~53%) for S11 ≤ −10 dB and 3 dB axial-ratio bandwidth of 1.95 GHz that is between 4.6 and 6.55 GHz (~35%). The antenna array has peak gain of 11 dBi at 5.5 GHz.

In this contribution a dual-band, dual-polarized microstrip antenna element for array applications is presented. The patch antenna is designed to operate simultaneously at around 30 and 20 GHz, the up- and downlink frequencies of modern Ka-band satellite communication systems. The antenna is smaller than half the freespace wavelength at 30 GHz to enable its utilization as array element of dual-band ground terminals. Integrating transmitter and receiver circuits allows, in turn, for a very compact active terminal solution. To minimize production cost, the design is carried out in standard multilayer printed circuit board technology. The antenna features two distinct polarization ports suitable for either dual linear or dual circular polarization if both ports are excited in quadrature. The single antenna design process is described in detail and simulation and measurement results are presented. Finally, different arrays based on this patch antenna are evaluated by simulation and measurements.

The purpose of this paper is twofold. It first describes how Microwaves were progressively organized by Professional Engineering Institutions in Europe in the years 1960–2000, essentially through individual efforts over many years. The first formal Microwave event organized in Europe was the European Microwave Conference in London, 1969, opening a series that continues as the European Microwave Week. It then shows that, over the same period of time, the Institute of Radio Engineers (IRE), USA, which merged in 1963 with the American Institute of Electrical Engineers, USA, to form the Institute of Electrical and Electronic Engineers (IEEE), also became stronger in Europe. European IRE members developed the structure of the IRE in Western Europe, with a first Regional meeting in Geneva, 1962. The paper illustrates the development of both Microwave Engineering and IRE-IEEE in Europe in the period of time considered, thanks to the commitment of European individuals, some of whom have been active on both counts.