In this work, a new structure for the implementation of inline pseudoelliptic waveguide filters using non-resonating modes, based on asymmetric iris coupled transverse rectangular ridge resonators has been proposed. The basic structure is comprised of a ridge that is always centered and transverse to the waveguide center axis and has the ability to create a transmission zero (TZ) above or below the passband without involving any rotation of the ridge, thus enabling quicker design of the resulting filters by allowing the use of more efficient analysis tools like FEST3D, in addition to the more general purpose methods like HFSS. A centered ridge enables the ease of manufacturing through machining. The proposed structure makes use of rectangular waveguide's dominant TE10 mode as a non-resonating mode to create an alternate energy path from source to load, thus realizing a TZ, while the asymmetric irises excite the ridge resonator, enabling the overall structure to act as a singlet capable of producing both a pole and a TZ. A third-order filter with one TZ and a fifth-order filter with two TZs have been designed and manufactured. Measured results show good consistency with the simulated data, validating the viability of the proposed structure.

In this paper, we present a miniaturized ultra-wideband (UWB) bandpass filter (BPF) with multiple transmission zeros (TZs), which is based on transition technology of microstrip with short-circuited coplanar waveguide (CPW). The ground plane of the BPF contains a multiple mode resonator (MMR)-based CPW which is capacitively linked through the dielectric to two open-circuited microstrip lines on the top. The MMR is initially designed to allocate its lowest three resonant modes quasi-equally inside the designated UWB spectrum (3.1–10.6 GHz). This is followed by optimization of microstrip lines to provide a good broadband response possessing minimum insertion loss, two TZs at the lower and upper passband edges that improve selectivity and a wide stopband with appreciable attenuation. Later, multiple-folded split ring resonators are coupled to the BPF to inject dual passband TZs. The predicted theory in simulation is verified against measured result and is found to be in good agreement. The prototype covers a substrate area of only 14.6 × 9.2 mm2.

The current paper describes the design of a fourth-order compact narrow-band hairpin-line bandpass filter centered at 2.5 GHz and enhanced stopband suppression ~38 dB required for wireless local area network (IEEE802.11b). The size reduction of 24% has been achieved for a conventional hairpin-line filter with a second-order inward folding of the open-end arms with an improvement in the skirt characteristics. However, the folding mechanism has been overshadowed by the presence of spurious harmonics with an attenuation level of <10 dB. Subsequently, L-shaped spurlines with optimum dimensions have been incorporated in the coupled arms of the folded hairpin-line cells. Three fourth-order filters have been designed with the incorporation of spurlines in different coupling regions, fabricated, and tested experimentally. Accordingly, an extended stopband with a rejection level of 38 dB up to 4.48f0 and a size reduction of 18% over the conventional hairpin-line filter has been achieved.

Full duplex (FD) could potentially double wireless communications capacity by allowing simultaneous transmission and reception on the same frequency channel. A single antenna architecture is proposed here based on a modified rat-race coupler to couple the transmit and receive paths to the antenna while providing a degree of isolation. To allow the self-interference cancellation (SiC) to be maximized, the rat-race coupler was made tuneable. This compensated for both the limited isolation of the rat race and self-interference caused by antenna mismatch. Tuneable operation was achieved by removing the fourth port of the rat race and inserting a variable attenuator and variable phase shifter into the loop. In simulation with a 50 Ω load on the antenna port, better than −65 dB narrowband SiC was achieved over the whole 2.45 GHz industrial, scientific and medical (ISM) band. Inserting the S-parameters of a commercially available sleeve dipole antenna into the simulation, better than −57 dB narrowband SiC could be tuned over the whole band. Practically, better than −58 dB narrowband tuneable SiC was achieved with a practical antenna. When excited with a 20 MHz Wi-Fi signal, −42 dB average SiC could be achieved with the antenna.

In this paper, a wideband ultrathin metasurface absorber is investigated. The proposed absorber comprises a periodic array of a unit cell ring structure. The ring structure and patch inside are tuned to realize the desired frequency bandwidth. The structure has a frequency bandwidth of 7.4 GHz with a center frequency of 15 GHz and fractional bandwidth of 50%. Simulated and measured results show that the absorption at normal incidence is above 90% in the frequency range of 11.3–18.7 GHz. Furthermore, the thickness of the structure is 1.6 mm. The physical mechanism of the metasurface absorber has been analyzed and justified experimentally.

In this paper, a small ultra-wideband (UWB) antenna with two stop bands by a compact electromagnetic bandgap (EBG) cell loaded with two new open meander slots is presented. With the coupling of the EBG cell to the feedline, the stop bands are formed. The designed EBG cell is a mushroom type that has the advantages of being able to independently control the stop bands, high responsiveness selectivity of stop bands, easy switching, the need for fewer EBG cells, and low impact on the working characteristics of the antenna. To have a better understanding of the proposed EBG mechanism, characteristic mode analysis is used. The size reduction of the suggested antenna is obtained by halving the reference antenna relative to the axis of symmetry. The measurement results for −10 dB adaptation are from 2.73 to 13 GHz with stop bands at 3.51 GHz (12.9%) and 5.34 GHz (14.1%). The radiation behavior of the minimized antenna is similar to that of a reference antenna. Minimized UWB antenna with transmission function and group delay with small variations in the operating frequency range is suitable for small multiple-input and multiple-output (MIMO) and diversity systems.

This paper reports a bi-port, wideband, parasitic-fed, single/shared patch antenna with enhanced interport isolation for 2.4 GHz in-band full duplex (IBFD) applications. The employed parasitic feeding provides comparatively the wider impedance bandwidth and better gain for the presented antenna. The improved self-interference cancellation (SIC) levels across the required bandwidth are obtained through differentially-driven receive (Rx) mode operation. The differential Rx operation performs effective cancellation of in-band self-interference (SI) through signal inversion mechanism to achieve the additional isolation on the top of the intrinsic isolation of polarization diversity. The validation model for the presented antenna features ≥88 dB peak isolation between the dual-polarized Tx and Rx ports. In addition, the measured Tx–Rx isolation for prototype is >70 dB across the 10 dB return loss bandwidth of 100 MHz (2.42–2.52 GHz). The measured gain for each mode is better than 7.0 dBi. The novelty of this work is that compared to previously reported designs, the presented antenna offers wider impedance bandwidth and improved SIC levels in addition to superior gain performance. To the best of our knowledge, this is the first single/shared patch antenna which provides better than 70 dB interport isolation across the 10 dB return loss bandwidth of 100 MHz along with 7.0 dBi gain for Tx/Rx modes.

A mathematical model of variable inclination continuous transverse stub (VICTS) antenna for low sidelobe design is proposed in this paper. VICTS antenna is an antenna with continuous transverse stubs on the parallel-plate waveguide and additional branches attached to the transverse stubs to generate radiation. The antenna using this technique has high aperture efficiency and keeps a significant solution for high-gain antenna. However, the sidelobe level (SLL) of this antenna is relatively high and increases continuously as the pitch angle decreases. This paper presents a fast calculation model for the SLL of VICTS antennas using leaky-wave theory and antenna array theory. The full-wave simulation results and model calculation results are in good agreement, so this model can be used for SLL suppression of VICTS antennas in different frequency bands. By controlling the aperture field distribution to be tapered, the SLL is suppressed to − 23.7 dB using this mathematical model.

In this paper, a tri-band metamaterial (MTM) loaded compact monopole antenna is proposed. In the first step of design procedure, a rectangular monopole antenna is improved by replacing the corresponding rectangular patch with a ring resonator. As a result, the first obtained operating frequency is decreased from 2.95 to 2.46 GHz. Then, this operating frequency is reduced to 2.02 GHz utilizing an MTM geometry in the antenna structure. The geometry parameters of the proposed antenna are optimized to provide the applicability for 3G, WLAN, and WiMAX applications. The impedance bandwidths of 600, 1080, and 220 MHz are obtained at 2.02–2.62, 3.48–4.56, and 5.12–5.34 GHz, respectively. Moreover, the equivalent circuit of the proposed antenna has been extracted. The proposed equivalent circuit model is validated through a comparison with corresponding simulation results. The proposed antenna is compact, low profile, via-less, and provides easy fabrication. Considering the first resonance frequency, a compactness of 32% is achieved in comparison to the corresponding unloaded monopole antenna.

In this paper, a compact stepped slot antenna for ultra-wideband (UWB) applications is proposed. A very small size and UWB bandwidth operation are achieved by integrating a stepped slot in the back side of the antenna. This stepped slot is excited by using a 50 Ω-feed line in the top side of the antenna. The antenna is characterized by an impedance bandwidth between 3.05 GHz and more than 12 GHz. The dimensions of the antenna are 17 mm × 8 mm × 1.27 mm, which leads to the most compact size compared with other works in the literature. The integrated stepped slot is divided into additional elementary slots, where each elementary slot has a matching point. Adding these elementary slots allows to increase further the operating bandwidth. The radiation pattern of the compact stepped slot antenna is omnidirectional in the H-plane and bidirectional in the E-plane. The measurement results agree well with the simulated ones in terms of impedance matching and radiation pattern.

This paper presents a compact dual-band filtering antenna without extra employing of filter structures. The antenna is designed using a planar dual-composite right/left-handed (D-CRLH) transmission line unit cell, where the filtering function is achieved through current cancellation between the D-CRLH resonators. The antenna is designed to function at 3.0 and 5.1 GHz, which can serve different WLAN applications. The antenna is a co-planar waveguide fed with a very compact size of only 30 × 16 mm2. Compared to the conventional patch antenna, the antenna size is only 17% at 3.0 GHz and 31% at 5.1 GHz. Despite the small size, the antenna preserves a good omni-directional radiation pattern at the two resonant frequencies with a measured realized gain of 2 and 2.7 dB, respectively. At the stopband in-between the two resonant bands, the reflection coefficient is almost 0 dB at 4.25 GHz and complete non-radiation is proved with a −11 dB measured realized gain. The different antenna filtering functions are verified by full-wave simulation and measurements.

This study presents a novel configuration of a cuboidal quad-port ultra-wideband multiple-input and multiple-output antenna with WLAN rejection characteristics. The designed antenna consists of four F-shaped elements backed by a partial ground plane. A 50 Ω microstrip line is used to feed the proposed structure. The geometry of the suggested antenna exhibits an overall size of 23 × 23 × 19 mm3, and the antenna produces an operational bandwidth of 7.6 GHz (3.1–10.7 GHz). The notched band characteristic at 5.4 GHz is accomplished by loading a pair of spiral electromagnetic bandgap structures over the ground plane. Besides this, other diversity features such as envelope correlation coefficient, and diversity gain are also evaluated. Furthermore, the proposed antenna system provides an isolation of −15 dB without using any decoupling structure. Therefore, to validate the reported design, a prototype is fabricated and characterized. The overall simulated performance is observed in very close agreement with it's measured counterpart.

A low-profile, wideband dual-polarized 1 × 2 multiple-input-multiple-output (MIMO) antenna with frequency selective surface (FSS) decoupling technique is presented. Low profile is realized with two different artificial magnetic conductor (AMC) cells out of which one operates at 3.5 GHz and other with dual band at 3.1 and 4.5 GHz. The proposed antenna height is maintained at 0.125λ0 which is significantly reduced when compared with the conventional perfect electric conductor (PEC) ground plane. Wideband dual polarization is enabled by two pairs of bow-tie antenna elements surrounded by a square ring placed in the orthogonal orientation. To mitigate the near-field coupling in 1 × 2 MIMO an FSS wall is constructed with wide band stop characteristics from 2.85 to 4.75 GHz. Measured results show by inserting FSS wall vertically, coupling reduction is improved by 27 dB over the existing coupling and the antenna exhibits a bandwidth of 57.14% (2.95–4.95 GHz) for VSWR<2 with port isolation of more than 25 dB for entire band of operation.

To solve the problems of low gain, narrow bandwidth, and poor radiation directivity of conventional ground penetrating radar antenna, this paper proposes an ultra-wideband and high-gain antipodal tapered slot antenna (ATSA) with planar metamaterial lens. As a constituent part of this lens, a new non-resonant metamaterial unit cell is introduced and analyzed by the full-wave simulation tool. The single-layer planar lens composed of the designed unit cells with different sizes is placed in the maximum radiation direction of the ATSA to greatly enhance its radiation capability. The proposed planar lens antenna has a wide impedance bandwidth of 107.4% (2.41–8 GHz) and −3 dB gain bandwidth of 54.5% (4–7 GHz), respectively. The gain increases averagely by 6.0 dB in the whole operating frequency band, and the peck gain reaches 15.4 dBi at 5.5 GHz. And its excellent performance shows a high application prospect in ground penetrating radar and microwave imaging system.

This paper presents a comprehensive review of symmetrically shaped antennas in terms of antenna size, dielectric materials, resonating band, peak gain, radiation pattern, simulating tools, and their applications. In this article, flower shape, leaf shape, tree shape, fan shape, Pi shape, butterfly shape, bat shape, wearable, multiband, monopole, and fractal antennas are discussed. Further, a survey of previously reported bandwidth enhancement techniques of microstrip patch antenna like introduction of thick and lower permittivity substrate, multilayer substrate, parasitic elements, slots and notches, shorting wall, shorting pin, defected ground structure, metamaterial-based split ring resonator structure, fractal geometry, and composite right-hand/left-handed transmission line approach is presented. The physics of these techniques has been discussed in detail which is supported by circuit theory model approach.