The aviation industry relies on accurate models. These models are used to predict an aircraft system’s outputs, and thus allow an understanding of the parameters involved, which could lead to system improvements. This study focuses on the engine modelling of an aircraft, and on its experimental validation using the Cessna Citation X Research Aircraft Simulator designed by CAE Inc., equipped with a level D Flight Dynamics toolbox. Level D is the highest rank attributed by the Federal Aviation Administration FAA certification authorities for flight dynamics. The proposed model aims to predict the thrust and the fuel consumption for various altitudes, Mach numbers and throttle lever angles (TLA). Different generic static models, which correspond to their steady state, from the literature, were used in this study; however, most of them were validated under restricted hypotheses. An optimisation algorithm was used in order to tune the static model parameters with the set of identification flight test data. Another set of data was then used in order to validate the identified model. Furthermore, a dynamic model corresponding to the transient operations was identified. TLA steps, impulses and ramp perturbations were performed in order to identify the system response, and to validate system dynamic model with other flight tests than the identification tests.

This study focuses on the co-operative salvo attack problem of multiple missiles against a stationary target under jointly connected switching topologies subject to time-varying communication delays. By carefully exploring certain features of the typical pure proportional navigation guidance law, a two-stage distributed guidance scheme is proposed without any information on time-to-go in this study to realise the simultaneous attack of multiple missiles. In the first guidance stage, a co-operative guidance law is proposed using local neighbouring communications only to achieve consensus on range-to-go and heading error to provide favourable initial conditions for the latter phase, in which switching topologies and time-varying communication delays are taken into account when obtaining sufficient conditions of consensus in terms of linear matrix inequalities. Then, missiles disconnect from each other and are guided individually by the typical pure proportional navigation guidance law with the same navigation gain to realise salvo attack in the second guidance phase. Finally, numerical simulations are carried out to clearly validate the theoretical results.

In this study, an improved fluid–structure interaction (FSI) analysis method is developed for a flapping wing. A co-rotational (CR) shell element is developed for its structural analysis. Further, a relevant non-linear dynamic formulation is developed based on the CR framework. Three-dimensional preconditioned Navier–Stokes equations are employed for its fluid analysis. An implicit coupling scheme is employed to combine the structural and fluid analyses. An explicit investigation of a 3D plunging wing is conducted using this FSI analysis method. A further investigation of this plunging wing is performed in relation to its operating condition. In addition, the relation between the wing’s aerodynamic performance and plunging motion is investigated.

Values are important in understanding the managerial behaviour. Values are the unique criteria that enable people to become conscious of social relations and duties. We contribute to this understanding through determining the values which affect an organisation’s business approach by providing evidence from a comparative study of various airports through a questionnaire method. The study was carried out with 163 participants and factor analysis was used to reduce the complexity of a data set so that it becomes easier to use the data in applied settings. Ranking analysis was used to get the values hierarchy of managers. This hierarchy-addicted culture helps to understand corporate sustainability and loyalty. Managing values increases quality and retains sustainability. Further suggestions are made regarding values that should be taken into consideration for achieving corporate strategies, whether operating regionally or globally. This study contributes towards improving awareness on the effects of values in business management in both theory and practice, along with their limitations. The analysis shows that there is a conformity between organisational and individual values.

Generally, earth rotating and non-spherical perturbation of the earth in re-entry motion model are simplified using the standard trajectory guidance method. The re-entry motion is also simplified to horizontal motion and vertical motion and controlled, respectively. The simplification of re-entry motion model will lead to loss of motion accuracy and location accuracy. The direct decomposition will lead to the reduction of control accuracy because the horizontal motion and the vertical motion are coupled in re-entry. To improve the standard trajectory guidance method, the standard trajectory guidance method based on decoupling control variables and waypoint is proposed in this paper. The proposed guidance method will not simplify earth rotating and non-spherical perturbation of the earth in motion equation or decompose the re-entry motion to horizontal motion and vertical motion. Trajectory waypoint is adopted to reduce the change frequency of tracking states, because tracking states change frequently if the entire standard trajectory is tracked in real time.

The eddy dissipation model (EDM) is analysed with respect to the ability to address the turbulence–combustion interaction process inside hydrogen-fuelled scramjet engines designed to operate at high Mach numbers (≈7–12). The aim is to identify the most appropriate strategy for the use of the model and the calibration of the modelling constants for future design purposes. To this end, three hydrogen-fuelled experimental scramjet configurations with different fuel injection approaches are studied numerically. The first case consists of parallel fuel injection and it is shown that relying on estimates of ignition delay from a 1D kinetics program can greatly improve the effectiveness of the EDM. This was achieved through a proposed zonal approach. The second case considers fuel injection behind a strut. Here the EDM predicts two reacting layers along the domain which is in agreement with experimental temperature profiles close to the point of injection but not the case any more at the downstream end of the test section. The first two scramjet test cases demonstrated that the kinetic limit, which can be applied to the EDM, does not improve the predictions in comparison to experimental data. The last case considered a transverse injection of hydrogen and the EDM approach provided overall good agreement with experimental pressure traces except in the vicinity of the injection location. The EDM appears to be a suitable tool for scramjet combustor analysis incorporating different fuel injection mechanisms with hydrogen. More specifically, the considered test cases demonstrate that the model provides reasonable predictions of pressure, velocity, temperature and composition.