Field studies were conducted to evaluate weed control in herbicide-resistant canola in Georgia. The resistant canola cultivars and respective herbicides were ‘Pioneer 45A76’ and imazamox, ‘Hyola 357RR’ and glyphosate, and ‘2573 Invigor’ and glufosinate. Weed seed of Italian ryegrass and wild radish were sown simultaneously in October with canola and control of these species was evaluated along with other naturally occurring weeds. Herbicide treatments for the respective herbicide-resistant canola cultivar were imazamox at 0.035 and 0.071 kg ai/ha, glyphosate at 0.84 and 1.64 kg ae/ha, and glufosinate at 0.5 and 1.0 kg ai/ha. Herbicides were applied at one– two-leaf (LF) and three–four-LF canola stages. There was no significant injury to any canola cultivar as a result of herbicide rate or timing of application. By midseason (February), imazamox effectively controlled wild radish, henbit, and shepherd's-purse at both rates and at both timings. When applied to three–four-LF canola, the higher rates of glyphosate and glufosinate were required to provide 75% or greater control of Italian ryegrass, wild garlic, and henbit. Glufosinate did not adequately control wild radish at either rate or application timing. Greenhouse experiments provided similar results.

Three field trials were established from 2001 to 2003 in Ontario to determine the effect of foramsulfuron POST (35 and 70 g ai/ha), isoxaflutole PRE (105 and 210 g ai/ha), and isoxaflutole plus atrazine PRE (105 + 1063 and 210 + 2126 g ai/ha) applied in the previous years to field corn on cranberry, black, kidney, and white (navy) bean. Foramsulfuron residues did not cause visible injury, or reductions in shoot dry weight or yield of dry bean 1 yr after application in corn. In contrast, visual injury across the four market classes varied from 4 to 37% 1 yr after application of isoxaflutole, and from 30 to 54% 1 yr after application of isoxaflutole plus atrazine. Isoxaflutole residues reduced shoot dry weight and yield as much as 81 and 44% in cranberry, 52 and 39% in black, 53 and 19% in kidney, and 42 and 19% in white bean, respectively. Isoxaflutole plus atrazine residues reduced shoot dry weight and yield as much as 87 and 64% in cranberry, 75 and 61% in black, 71 and 46% in kidney, and 65 and 33% in white navy bean, respectively. Injury was not detected regardless of market classes 2 yr after application of isoxaflutole alone or in tank mix with atrazine. Based on these results, it is recommended that none of the market classes of dry bean tested in this study should be grown 1 year after an application of isoxaflutole or isoxaflutole plus atrazine. A recropping interval of 2 years is currently recommended following applications of isoxaflutole or isoxaflutole plus atrazine for these market classes of dry bean.

Field studies were conducted at three locations during both 2002 and 2003 to evaluate weed control and response of glyphosate-resistant (GR) corn to glyphosate or nicosulfuron plus atrazine applied POST at three application timings with and without alachlor plus atrazine applied PRE. The POST herbicides were applied timely (5- to 9-cm weeds) or applications were delayed 1 or 2 wk. All treatments, except the weedy check, were followed by glyphosate postemergence-directed (PDIR) 4 wk after the timely POST application. Common lambsquarters, common ragweed, Palmer amaranth, prickly sida, and smooth pigweed were controlled at least 94% regardless of PRE or POST treatments. Large crabgrass and fall panicum were controlled at least 96% by glyphosate regardless of PRE herbicide or POST application timing. In contrast, control by nicosulfuron plus atrazine POST in the absence of PRE herbicide decreased as application was delayed. Sicklepod was controlled at least 94% when POST herbicides were applied timely, but control by both POST herbicide treatments decreased with delayed application regardless of PRE herbicide. Tall morningglory was controlled 93% or greater by POST herbicides applied timely. Control by both POST herbicide treatments decreased as application was delayed, with glyphosate being affected more by timing than nicosulfuron plus atrazine. Corn grain yield was similar with glyphosate and nicosulfuron plus atrazine. Yield was unaffected by POST application timing when PRE herbicides were included. Without PRE herbicide, grain yield decreased as POST herbicide application was delayed.

Dose-response experiments were conducted in a greenhouse on a biotype of johnsongrass from Washington County, Mississippi, to determine the level of resistance to the aryloxyphenoxypropionate (AOPP) herbicide fluazifop-P-butyl and the cyclohexanedione (CHD) herbicides clethodim and sethoxydim. Both seedling and rhizomatous plants were evaluated. Resistant/susceptible (R/S) ratios were calculated based on GR50 values (the rate required to reduce shoot dry biomass, expressed as a percent of the control, 50%). The GR50 values for the resistant and susceptible seedling plants were 110 and 10 g ai/ha for clethodim, 193 and 34 g ai/ha for fluazifop-P-butyl, and 265 and 48 g ai/ha for sethoxydim, resulting in R/S ratios of 11.0, 5.7, and 5.5, respectively. The GR50 values for the resistant and susceptible rhizomatous plants were 609 and 39 g/ha for clethodim, 657 and 29 g/ha for fluazifop-P-butyl, and 668 and 30 g/ha for sethoxydim, resulting in R/S ratios of 15.6, 22.7, and 22.3, respectively.

Experiments were conducted to determine the inheritance of resistance in crosses between imazethapyr-resistant rice and red rice. Past experiments on red rice control, using the Clearfield rice technology, resulted in outcrossing between Clearfield rice and Stuttgart strawhull red rice. The F2 generation of these spontaneous crosses were characterized with respect to inheritance of imazethapyr resistance, leaf color and leaf pubescence, and seed shattering, pubescence, color, and size. Agronomic traits of hybrids were also observed in relation to their parents. To determine the segregation of resistance among F2 phenotypes, the response of three- to four-leaf plants to imazethapyr was scored 3 wk after application as resistant (R, no imazethapyr symptoms), susceptible (S, death of plants), or intermediate (I, stunted plants). R, I, and S phenotypes segregated in a 1:2:1 ratio in the F2 generation. Two- or three-gene inheritance was documented for leaf and seed characteristics. A wide range in onset of flowering (70 to 130 d after planting) was observed in F2 families, although 6% of the plants did not flower during the growing season. F2 plants were taller and had more tillers than any of their parents. Resistance to imazethapyr is associated with a single, incompletely dominant allele.

Field experiments were conducted during 3 yr in Thessaloniki, northern Greece, to determine the efficacy of various herbicides applied alone or in mixtures POST on hoary cress grown in winter wheat. Also, the efficacy of these herbicides on hoary cress generated from seed or root fragments was investigated in pot experiments. All herbicides except for ioxynil plus bromoxynil provided 90 to 100% control of hoary cress generated from seed and root fragments grown in pots. Ioxynil plus bromoxynil gave 84% control of hoary cress generated from seed, but only 66% control of plants generated from root fragments. In the field, mecoprop plus dicamba, imazamethabenz plus mecoprop plus dicamba, and triclopyr applied at the four- to eight-leaf stage provided, respectively, 87, 76, and 83% control of hoary cress (averaged over year and assessment time). Thifensulfuron plus tribenuron provided only 29% control. Chlorsulfuron plus dicamba, clopyralid plus MCPA, 2,4-D plus metosulam, and fluroxypyr provided intermediate hoary cress control. Furthermore, the least hoary cress emergence 52 wk after treatment appeared in plots treated with triclopyr. In addition, wheat grown in plots treated with mecoprop plus dicamba yielded more than wheat treated with the other herbicide treatments, and 55% more than wheat grown in nontreated plots. The results of this study indicate that very good control of hoary cress and high wheat yield can be obtained by the application of mecoprop plus dicamba at the four- to eight-leaf weed growth stage.

The effects of microtopographic position on soil microenvironment and weed populations in ridge-tilled soybean were evaluated on three farms in Iowa in 1989 and 1990. In both years, over all weed species (primarily giant foxtail, green foxtail, yellow foxtail, redroot pigweed, and Pennsylvania smartweed), seedling emergence was highest in late May and early June, with few seedlings emerging after mid-June. Weed populations were highest in May and early June, after which rotary hoeing and cultivation reduced weed numbers in all plots. Microtopographic position (row, shoulder, and furrow) had a large effect on soil microenvironment and weed populations. Furrows were the wettest position through most of the growing season. Rows were the warmest position early in the season and the coolest position late in the season. Cumulative weed emergence early in the season was closely related to growing degree days, which accumulated faster in the row position than the furrow position. Following rotary hoeing and cultivation, the row position had significantly more total weeds than the shoulder and furrow positions on all farms in August of both years.

Field experiments were conducted in 2002 and 2003 to evaluate total POST weed control in corn with mixtures of mesotrione, atrazine, and the commercial mixture of nicosulfuron plus rimsulfuron plus atrazine at registered and reduced rates. Treatments were compared with nicosulfuron plus rimsulfuron plus atrazine POST, and S-metolachlor plus atrazine PRE alone and followed by (fb) nicosulfuron plus rimsulfuron plus atrazine POST. All treatments controlled common lambsquarters 8 wk after the postemergence treatments (WAPT). Common ragweed control with POST mesotrione plus nicosulfuron plus rimsulfuron plus atrazine combinations was greater than 89%. Mesotrione plus the registered rate of nicosulfuron plus rimsulfuron plus atrazine POST controlled common ragweed more effectively than the PRE treatment alone. Addition of atrazine to mesotrione improved common ragweed control by at least 38 percentage points over mesotrione alone. Nicosulfuron plus rimsulfuron plus atrazine at the registered rate and in mixtures with mesotrione controlled morningglory species (pitted and ivyleaf morningglory) 89 to 91%. Large crabgrass control varied between 2002 and 2003. In 2002, large crabgrass control was 58 to 76% with all POST treatments, but in 2003, nicosulfuron plus rimsulfuron plus atrazine POST alone controlled large crabgrass greater than 86%. Large crabgrass was more effectively controlled by treatments with S-metolachlor plus atrazine PRE than by the total POST treatments in 2002. Giant foxtail was controlled at least 97% with nicosulfuron plus rimsulfuron plus atrazine treatments. S-metolachlor plus atrazine PRE fb nicosulfuron plus rimsulfuron plus atrazine POST controlled all weed species greater than 85%. Corn yields by total POST treatment combinations of mesotrione plus either rate of nicosulfuron plus rimsulfuron plus atrazine were comparable to S-metolachlor plus atrazine PRE alone or fb nicosulfuron plus rimsulfuron plus atrazine POST.

Field studies were conducted to assess the tolerance of seashore paspalum (‘Salam’) to postemergence (POST) herbicides in Florida in 2000 and 2001. POST applications of bentazon (2,200 g/ha), clopyralid (420 g/ha), dicamba (280 g/ha), halosulfuron (70 g/ha), imazaquin (420 g/ha), mecoprop + 2,4-D + dicamba (160 + 180 + 40 g/ha), metsulfuron (30 g/ha), and quinclorac (1,700 g/ha) resulted in ≤10% injury 7 and 15 d after treatment (DAT), indicating their safety for POST application. Clethodim (280 g/ha) and sethoxydim (310 g/ha) caused 67 and 46% injury, respectively, 15 DAT averaged across 2000 and 2001. Ethofumesate was inconsistent between years, causing 30 and 60% injury 7 and 15 DAT, respectively, in 2000, but only 5 and 13% 7 and 15 DAT, respectively, in 2001. Imazapic and trifloxysulfuron-sodium caused an average of 47% injury 7 DAT in 2000 and 45% injury 15 DAT in 2001. Clethodim, ethofumesate, imazapic, sethoxydim, and trifloxysulfuron-sodium can not be safely applied POST to Salam seashore paspalum; however, bentazon, clopyralid, dicamba, halosulfuron, imazaquin, mecoprop + 2,4-D + dicamba, metsulfuron, and quinclorac are safe.

Response of ‘Dixie’, ‘Lemondrop’, ‘Multipik’, ‘Superpik’, and ‘Seneca Prolific’ summer squash to halosulfuron PRE or POST at 0.036, 0.053, and 0.072 kg ai/ha, or halosulfuron PRE fb halosulfuron POST at 0.018 fb 0.018, 0.027 fb 0.027, and 0.036 fb 0.036 kg/ha was field evaluated in 1997 and 1998. All halosulfuron treatments and rates reduced the height of cultivars 17–19% at 6 WAP (weeks after planting) and summer-squash injury (chlorosis and necrosis of crop foliage) was 6, 14, and 11% from halosulfuron PRE, POST, and PRE fb POST, respectively. Early summer-squash flowering was reduced 32–82% by halosulfuron, resulting in reduced early yields. Dixie was the cultivar most tolerant to halosulfuron. Early flowering of Dixie was reduced 32–36% compared to 32–82% for the other cultivars. Marketable yield of summer squash was reduced 20–30% by all rates of halosulfuron when averaged over all application timings. Marketable yield of Seneca Prolific, Superpik, Dixie, Multipik, and Lemondrop was reduced 0–17% by halosulfuron PRE. Halosulfuron POST or PRE fb POST reduced marketable yield of all summer-squash cultivars by 25–46%. Thus, summer squash was not tolerant of POST halosulfuron; however, Dixie, Multipik, Seneca Prolific, and Superpik exhibited tolerance to halosulfuron PRE.

Field experiments were conducted during 2003 and 2004 to compare the effectiveness of KIH-485 and S-metolachlor for PRE weed control in no-tillage and conventional-tillage corn. Longspine sandbur control increased as KIH-485 or S-metolachlor rates increased in conventional-tillage corn, but control did not exceed 75% when averaged over experiments. Both herbicides controlled at least 87% of green foxtail with the exception of no-tillage corn in 2004, when KIH-485 was more effective than S-metolachlor at lower rates. Palmer amaranth control ranged from 85 to 100% in 2003 and 80 to 100% in 2004, with the exception of only 57 to 76% control at the lowest two S-metolachlor rates in 2004. Puncturevine control exceeded 94% with all treatments in 2003. In 2004, KIH-485 controlled 86 to 96% of the puncturevine, whereas S-metolachlor controlled only 70 to 81%. Mixtures of atrazine with KIH-485 or S-metolachlor generally provided the most effective control of broadleaf weeds studied.

Field experiments were conducted at the Caddo Research Station near Ft. Cobb, OK and at the Agronomy Research Station near Perkins, OK to measure the effects of seven crownbeard (Verbesina encelioides) densities on peanut (Arachis hypogaea) yield. The seven densities evaluated were 0 (the weed-free check), 0.2, 0.4, 0.8, 1.6, 2.4, and 3.2 weeds/m of row. Data collected consisted of dry weed biomass and peanut yields. Correlation between weed density and dry weed biomass, dry weed biomass and peanut yield (kg/ha), dry weed biomass and peanut yield loss (percentage of check), weed density and peanut yield (kg/ha), and weed density and peanut yield loss (percentage of check) were evaluated. For each weed/m of row, dry weed biomass increased by 0.34 kg/m row. Dry weed biomass was a good predictor of peanut yield. For each kilogram of dry weed biomass/ m row, a 1900-kg/ha or 46.3% reduction in peanut yield occurred. Weed density was also a good predictor of peanut yield. A 559-kg/ha reduction or 16% increase in peanut yield loss occurred for each weed/m row. Peanut yield was reduced approximately 50% when crownbeard density increased to 3.2 weeds/m row.

Field studies were conducted at four locations over a 2-year period to evaluate the utility of soil-applied herbicides and glyphosate timing for weed control and soybean yield. Pendimethalin, S-metolachlor plus metribuzin, and flufenacet plus metribuzin were applied pre-emergence (PRE) alone or followed by glyphosate applied early postemergence (EPOST), late postemergence (LPOST), or EPOST plus LPOST. Soil-applied herbicides or glyphosate alone failed to control (<45%) broadleaf signalgrass in 2003 due to late-season rainfall, which accounted for a late flush of growth. In 2004, soil-applied herbicides alone controlled 79–100% broadleaf signalgrass, whereas glyphosate alone or in combination with soil-applied herbicides controlled at least 99%. Barnyardgrass and tall waterhemp were controlled at least 87% with soil-applied herbicides alone and at least 95% when glyphosate was used alone or in combination with a soil-applied herbicide. Soybean yield varied, but at only one location did herbicide treatments produce higher yields than the untreated check. Under low to moderate weed pressure, the use of a soil-applied herbicide followed by glyphosate failed to increase net returns over soil-applied herbicides alone.

Field studies were conducted at Shiraz, Iran, during 2000 and 2001 to investigate the effect of separate and combined herbicide treatments on weed control and corn yield. Separate and combined herbicide treatments included 14 combinations applied at two rates. Herbicides reduced weed biomass compared with the weedy check. In both years, maximum reduction in weed biomass was observed with atrazine plus alachlor at 1 + 2.44 and 1.5 + 1.92 kg ai/ha and minimum reduction in weed biomass was observed with rimsulfuron at 0.02 and 0.04 kg/ha. In 2000 and 2001, 2,4-D plus MCPA at 0.36 + 0.31 and 0.54 + 0.46 kg/ha, and alachlor plus 2,4-D plus MCPA at 1.92 + 0.54 + 0.46 kg/ha, and 2.44 + 0.36 + 0.31 kg/ha, controlled 80 to 100% of field bindweed and rimsulfuron at 0.02 and 0.04 kg/ha controlled 17 to 70% of field bindweed. All herbicide treatments controlled redroot pigweed 60 to 100%. In 2000, at 6 and 17 WAP, minimum biomass reduction of Chinese-lantern-plant was observed with 2,4-D plus MCPA at 0.36 + 0.31 and 0.54 + 0.46 kg/ha, and primisulfuron plus prosulfuron at 0.02 + 0.02 and 0.03 + 0.03 kg/ha. Rimsulfuron plus primisulfuron plus prosulfuron at 0.02 + 0.03 + 0.03 and 0.04 + 0.02 + 0.02 kg/ha reduced johnsongrass biomass 96 to 100% and the efficacy of rimsulfuron increased when tank mixed with primisulfuron plus prosulfuron. Results of both years showed that all herbicide treatments increased corn grain yield as compared with the weedy check. Maximum corn grain yield was obtained with combinations of atrazine plus alachlor at 1 + 2.44 and 1.5 + 1.92 kg/ha.

Weed management is often difficult and expensive in organic production systems. Clove oil is an essential oil that functions as a contact herbicide and may provide an additional weed management tool for use on organic farms. Burning nettle, purslane, and rye responses to 5, 10, 20, 40, and 80% v/v clove oil mixture applied in spray volumes of 281 and 468 L/ha were examined. Log-logistic curves were fitted to the nettle and purslane data to determine the herbicide dose required to reduce plant dry weight 50% (GR50) and 90% (GR90). A three-parameter Gaussian curve was fitted to the rye data. The GR50 and GR90 were largely unaffected by spray volume. Nettle dry weight was reduced by 90% with 12 to 61 L clove oil/ha, whereas 21 to 38 L clove oil/ha were required to reduce purslane biomass to the same level. Rye was not effectively controlled by clove oil. Clove oil controls broadleaf weeds at high concentrations, but its cost makes broadcast applications prohibitive, even in high-value vegetable production systems.

Field studies were conducted at Lewiston–Woodville and Rocky Mount, NC in 2001 and 2002 to evaluate weed control and peanut response to POST treatments of diclosulam at various rates and application timings. Diclosulam controlled common ragweed and entireleaf morningglory when applied within 35 d after planting (DAP). Common ragweed 61 cm tall was controlled ≥92% with 4 to 13 g ai/ha diclosulam and larger common ragweed (107 to 137 cm tall) were controlled ≥97% with 27 g/ha diclosulam. Common lambsquarters was controlled 62% or less with all diclosulam POST treatments following metolachlor applied PRE, which provided 48% control. Peanut injury was less than 15% with all diclosulam POST treatments and was transitory. In separate studies, POST diclosulam treatments did not affect peanut yield in a weed-free environment. Peanut yield in weedy environments was reduced as the diclosulam application timing was delayed because of early season weed interference. A linear relationship was observed between yield and application timing with yield decreasing as application timing was delayed. This yield response documents the importance of early season weed management for maximizing peanut yield potential. Virginia peanut varieties were not affected by different POST rates of diclosulam; however, early season peanut injury showed a linear and quadratic relationship with diclosulam rate and was less than 14% at rates as high as 71 g/ha, and was not apparent by late season.

No-till cropping is an option for growers needing to reduce soil erosion in the Palouse annual-cropped region of the Pacific Northwest, which is well suited for wheat production. A 6-yr field study was conducted to determine optimum levels of fertilizer and herbicide inputs in a no-till continuous wheat crop production system. Three levels of nitrogen (N) and two weed management levels (WML) were compared in a spring wheat (SW)–winter wheat (WW)–WW rotation through two rotation cycles. The high WML reduced weed densities about 50% compared with the low WML. In general, herbicide treatments were more effective on broadleaf weeds and may have facilitated a shift toward grass weeds. The high WML reduced grass weed biomass only at the reduced N levels, whereas the high WML reduced broadleaf weed density at all N levels. Variable environmental conditions affected wheat yield; however, yield tended to be highest where winter wheat immediately followed spring wheat. Nitrogen had little effect on weed density but increased crop yield about 13% with each increased N level. Crop yield was greater at the high versus low WML at each N level, even though weed density and biomass were reduced least between WMLs at the highest N level. The highest crop yield and net returns were obtained with the highest N and WML; however, none of the N and WML combinations were profitable.

Field experiments were conducted to study the effects of oxadiazon and oxyfluorfen on weeds and Syrian marjoram (Origanum syriacum L.) in the central Jordan Valley during the period from 1998 to 2001. Results showed that weed competition with marjoram for the whole growing period resulted in almost complete crop failure. Oxyfluorfen and oxadiazon applied preplanting or postplanting to marjoram controlled weeds effectively, resulted in significant increase in marjoram shoot fresh and dry weight yields and in more branches per plant compared with the weed-infested control. High marjoram yield was obtained with oxyfluorfen applied at 0.72 kg ai/ha in preplanting treatment and with oxadiazon at 1.25 and 0.75 kg ai/ha in pre- and postplanting treatments, respectively. In preplanting treatment, 0.36 kg ai/ha of oxyfluorfen was highly selective, but 1.44 kg ai/ha reduced marjoram yield. Conflicting results were obtained with oxadiazon under the same treatments. In postplanting, oxyfluorfen at 0.24 and 0.96 kg ai/ha significantly increased marjoram yield over the weed-infested control. However, the highest shoot dry weight of marjoram was obtained at 0.96 kg ai/ha of this herbicide. In contrast, the low rate (0.38 kg ai/ha) of oxadiazon was highly selective and increased marjoram yield, but the herbicide failed to increase yield beyond the weed-infested control when the higher rate (1.5 kg ai/ha) was used. Results showed that both oxyfluorfen and oxadiazon herbicides were highly selective and effective for weed control in Syrian marjoram, providing normal rates of both are used, although high rates of the two herbicides were also selective and increased marjoram yield over the weed-infested control.

The objectives of this research were to determine if adjuvants with water-repellent properties could reduce herbicide retention on foliage, and thereby absorption, of the spray solution and to determine if herbicide activity was maintained with a reduction in herbicide retention. Water-repellent adjuvants, DC 2-1322, DC 1-6184, and DC 772, were evaluated with three herbicides, isoxaflutole, pendimethalin, and flumioxazin, and on three crop species, cabbage, tomato, and wheat. The water repellents DC 2-1322 and DC 772 were ineffective with these herbicides and these crop species. DC 1-6184 effectively reduced spray retention for all three herbicides evaluated, regardless of formulation, on all three species. The efficacy of DC 1-6184 was more evident if the spray application was restricted to the plant foliage. The water-repellent DC 1-6184 has potential to decrease injury while maintaining weed control with certain herbicides.

Centipedegrass is a warm-season turf grass that has increased in popularity in recent years. However, more information is needed on the use of herbicides during centipedegrass establishment from seed, particularly in seed and sod production systems. The intent of this study was to evaluate turf-grass injury and weed control when atrazine, imazapic, imazethapyr, and simazine are applied immediately after seeding centipedegrass. Atrazine and simazine (applied at 1.1, 2.2, and 4.4 kg ai/ ha) injured centipedegrass less than 15% at 5 wk after treatment (WAT) in 2001. Imazethapyr and imazapic (applied at 0.04, 0.07, and 0.1 kg ai/ha) injured centipedegrass between 7 and 13%, 5 WAT, in 2001 and from 30 to 77% in 2002. Herbicide and application rate also affected centipedegrass cover. At 3 WAT, cover decreased with all herbicides as application rate increased. At 12 WAT in both years, centipedegrass cover increased as atrazine application rate increased and imazethapyr application rate decreased. Imazapic and simazine were less consistent, causing increases in cover one year and decreases, or no change, the next. Imazapic controlled Texas panicum 80 to 89% and was more effective than any other herbicide. Atrazine and simazine controlled crowfootgrass better than any other herbicide. Imazethapyr often injured centipedegrass and failed to control weeds. Atrazine effectively controlled grass and broadleaf weeds with minimal centipedegrass injury. Imazethapyr and imazapic were too injurious to permit usage during centipedegrass establishment from seed.