A 1.7 μm gain-switched thulium-doped all-fiber laser with a master oscillator power amplifier (MOPA) configuration, utilizing a bandpass fiber filter and a 1550 nm erbium/ytterbium-codoped fiber MOPA, is demonstrated. The influences of pump pulse parameters (repetition rate and pulse duration) and laser cavity structures (ring and linear) on the laser performances were experimentally investigated. To the best of our knowledge, the power quenching and drop were observed in the 1.7 μm gain-switched thulium-doped fiber lasers for the first time, resulting from the mode-locked-resembling operation and nonlinear effects. Moreover, the fiber ring-cavity laser was more stable than the linear-cavity laser in the time domain and power. Finally, a laser with a maximum average power of 1.687 W, a slope efficiency of 19.7%, a single-pulse energy of 16.87 μJ, a pulse width of 425 ns, a repetition rate of 100 kHz and a peak power of 39.69 W was obtained.

We report on a grating-free fiber chirped pulse amplifier (CPA) at 2.8 μm for the first time. The CPA system adopted Er:ZBLAN fiber with large anomalous dispersion as the stretcher and germanium (Ge) rods as the compressor with a compact structure. High-energy picosecond pulses of 2.07 μJ were generated at the repetition rate of 100 kHz. Using highly dispersive Ge rods, the amplified pulses were compressed to 408 fs with a pulse energy of 0.57 μJ, resulting in a peak power of approximately 1.4 MW. A spectral broadening phenomenon in the main amplifier was observed, which was caused by the special gain shape of the Er:ZBLAN fiber amplifier in operation and confirmed by our numerical simulation. This compact fiber CPA system at 2.8 μm will be practical and meaningful for application fields.

Multilayer dielectric gratings typically remove multiple-grating pillars after picosecond laser irradiation; however, the dynamic formation process of the removal is still unclear. In this study, the damage morphologies of multilayer dielectric gratings induced by an 8.6-ps laser pulse were closely examined. The damage included the removal of a single grating pillar and consecutive adjacent grating pillars and did not involve the destruction of the internal high-reflection mirror structure. Comparative analysis of the two damage morphological characteristics indicated the removal of adjacent pillars was related to an impact process caused by the eruption of localized materials from the left-hand pillar, exerting impact pressure on its adjacent pillars and eventually resulting in multiple pillar removal. A finite-element strain model was used to calculate the stress distribution of the grating after impact. According to the electric field distribution, the eruptive pressure of the dielectric materials after ionization was also simulated. The results suggest that the eruptive pressure resulted in a stress concentration at the root of the adjacent pillar that was sufficient to cause damage, corresponding to the experimental removal of the adjacent pillar from the root. This study provides further understanding of the laser-induced damage behavior of grating pillars and some insights into reducing the undesirable damage process for practical applications.

In strong-field physics experiments with ultraintense lasers, a single-shot cross-correlator (SSCC) is essential for fast optimization of the pulse contrast and meaningful comparison with theory for each pulse shot. To simultaneously characterize an ultrashort pulse and its long pedestal, the SSCC device must have both a high resolution and a large temporal window. However, the resolution and window in all kinds of single-shot measurement contradict each other in principle. Here we propose and demonstrate a novel SSCC device with two separate measurement channels: channel-1 for the large-window pedestal measurement has a moderate resolution but a large window, while channel-2 for the ultrashort pulse measurement has a small window but a high resolution; this allows the accurate characterization of the pulse contrast in a single shot. A two-channel SSCC device with a 200-fs resolution and 114-ps window has been developed and tested for its application in ultraintense lasers at 800 nm.

In this work, a confined-doped fiber with the core/inner-cladding diameter of 40/250 μm and a relative doping ratio of 0.75 is fabricated through a modified chemical vapor deposition method combined with the chelate gas deposition technique, and subsequently applied in a tandem-pumped fiber amplifier for high-power operation and transverse mode instability (TMI) mitigation. Notably, the impacts of the seed laser power and mode purity are preliminarily investigated through comparative experiments. It is found that the TMI threshold could be significantly affected by the seed laser mode purity. The possible mechanism behind this phenomenon is proposed and revealed through comprehensive comparative experiments and theoretical analysis. Finally, a maximum output power of 7.49 kW is obtained with the beam quality factor of approximately 1.83, which is the highest output power ever reported in a forward tandem-pumped confined-doped fiber amplifier. This work could provide a good reference and practical solution to improve the TMI threshold and realize high-power high-brightness fiber lasers.

A linearly polarized Laguerre–Gaussian (LP-LG) laser beam with a twist index $l = -1$ has field structure that fundamentally differs from the field structure of a conventional linearly polarized Gaussian beam. Close to the axis of the LP-LG beam, the longitudinal electric and magnetic fields dominate over the transverse components. This structure offers an attractive opportunity to accelerate electrons in vacuum. It is shown, using three-dimensional particle-in-cell simulations, that this scenario can be realized by reflecting an LP-LG laser off a plasma with a sharp density gradient. The simulations indicate that a 600 TW LP-LG laser beam effectively injects electrons into the beam during the reflection. The electrons that are injected close to the laser axis experience a prolonged longitudinal acceleration by the longitudinal laser electric field. The electrons form distinct monoenergetic bunches with a small divergence angle. The energy in the most energetic bunch is 0.29 GeV. The bunch charge is 6 pC and its duration is approximately $270$ as. The divergence angle is just ${0.57}^{\circ }$ (10 mrad). By using a linearly polarized rather than a circularly polarized Laguerre–Gaussian beam, our scheme makes it easier to demonstrate the electron acceleration experimentally at a high-power laser facility.

Spatiotemporal optical vortex (STOV) pulses carrying purely transverse intrinsic orbital angular momentum (TOAM) are attracting increasing attention because the TOAM provides a new degree of freedom to characterize light–matter interactions. In this paper, using particle-in-cell simulations, we present spatiotemporal high-harmonic generation in the relativistic region, driven by an intense STOV beam impinging on a plasma target. It is shown that the plasma surface acts as a spatial–temporal-coupled relativistic oscillating mirror with various frequencies. The spatiotemporal features are satisfactorily transferred to the harmonics such that the TOAM scales with the harmonic order. Benefitting from the ultrahigh damage threshold of the plasma over the optical media, the intensity of the harmonics can reach the relativistic region. This study provides a new approach for generating intense spatiotemporal extreme ultraviolet vortices and investigating STOV light–matter interactions at relativistic intensities.