A reflective linear-to-circular polarization converter based on dual frequency-selective structures (FSSs) is proposed and modeled to exhibit efficient wideband performance. The design utilizes a diagonal array of two connected circular patches as an effective anisotropy with regular current distribution in several successive resonances, resulting in orthogonal reflections with a 90° phase difference. The relevant upper-part characteristic is improved by using two separate square patches as a high-frequency resonator. This design with distinct key parameters leads to high overlapping and then excellent bandwidth and efficiency over 105% and 96%, respectively, with an axial ratio below 1.7 dB. A sophisticated equivalent circuit-admittance model including effective mutual coupling between two FSSs is extracted, featuring closed-form equations for the physical design. Different dielectric constants are studied on the converter, which offer controllable coverage in the range of 3–24 GHz (S, C, X, Ku, and K bands), variably. For actual validation, a very thin (0.04λ0 at 3.65 GHz) 8 × 8 array prototype was built and measured at different incident angles, showing angular stability up to 45° in 78% (6–14 GHz) bandwidth. This converter has potential applications in communication, spectroscopy, detection, and imaging in micro-, mm-, and THz-wave regions.

Liquid crystal microwave phased arrays (LC-MPAs) are regarded as an ideal approach to realize compact antennas owing to their advantages in cost, size, weight, and power consumption. However, the shortcoming in low radiation deflection efficiency has been one of LC-MPAs’ main application limitations. To optimize the steering performance of LC-MPAs, it is essential to model the channel imperfections and compensate for the phase errors. In this paper, a phase error estimation model is built by training a neural network to establish a nonlinear relationship between the near-field phase error and the far-field pattern, hence realizing fast calibration for LC-MPAs within several measured patterns. Simulations and experiments on a 64-channel, two-dimensional planar antenna were conducted to validate this method. The results show that this method offers precise phase error estimations of 3.58° on average, realizes a fast calibration process with several field-measured radiation patterns, and improves the performances of the LC-MPA by approximately 4%–10% in deflection efficiency at different steering angles.

This paper presents a low-profile six-beam antenna implemented by a compact two-layer 6 × 6 beamforming network (BFN) and a 6 × 2 slot antenna in substrate integrated waveguide (SIW) technology. The main components of the proposed 6 × 6 BFN are 3 × 3 multi-aperture couplers, interlayer hybrid couplers, and several phase shifters which are embedded on two microwave substrates. The proposed antenna has been designed, simulated, and fabricated for the frequency range of 28–32 GHz. The size of this antenna is 82 × 31.8 × 0.787 mm3, which can be a suitable choice for 5G applications due to its compact dimensions compared to similar works. Prototype testing shows that the proposed structure presents a stable beamforming performance both in simulation and measurement with good agreement. The antenna generates six radiation beams in directions ±9°, ±30°, and ±54° with good return losses and isolations.

With the development of the communication field, more and more communication devices need multiple single-frequency antennas to work simultaneously. However, using multiple single-frequency antennas results in larger sizes. The miniaturized and dual-band communication system has become a new development trend. This paper designs a dual-band filtering patch antenna based on a multimode resonator, which is cascaded. The filter resonator part adopts step impedance resonance for branch shunt design, which can flexibly control the center frequency of two frequency bands. The filtering antenna utilizes a dual-layer substrate structure and achieves an integrated design through coupling probe feeding. This reduces the horizontal dimensions and improves miniaturization. Multiple radiation nulls are introduced outside the two-passband, and roll-off characteristics are evident. In addition, this design realizes high selectivity in the operating band. The antenna has large gains of 1.71 dBi and 6.25 dBi. It has good filtering and radiation characteristics.

This article presents the design of a novel sigma slotted circular monopole antenna for wireless body area network applications. The design is proceeded with a sigma-shaped slot etched on the circular radiator with Rogers 4003C substrate. The size of the proposed antenna is 30 × 30 × 1 mm3. With partial ground plane, the bandwidth characteristics of the antenna have been enhanced. The designed antenna covers 2–10 GHz of the ultra wideband, thereby providing more than 106% bandwidth. The antenna exhibits high gain values of 1.95, 3.23, 3.46, and 5.95 dB at 2.45, 3.45, 5.8, and 9.5 GHz, respectively. The proposed design operates on off-body mode at 2.45 GHz and on-body mode at 5.8 GHz, thus acting as a dual-mode antenna. To ensure the health and safety measure, specific absorption rate analysis was done for both low and high values of input power and also with Cartesian and cylindrical human arm models. Bending analysis was also done. The time domain parameter group delay was also analyzed for the proposed antenna for on- and off-body scenarios. The prototype was fabricated, and validation of simulation results was done for free space and on-body scenarios.

This paper proposes a triple-band fractal slot antenna with enhanced gain operating at frequencies of 2.7, 3.5, and 4.8 GHz for microwave wireless power transmission. The antenna achieved more than 3 dB gain by preserving the symmetrical defected reflector structure behind it at a length of 0.54λ/4, where λ is the wavelength in free space at 2.7 GHz. A 50 Ω micro-strip line coupled at 66 mm length helps feed the triple band slot antenna. The purpose of a triple-band rectifier circuit with an impedance network is to convert the radio frequency (RF) signal into direct current. The measurements reveal that the antenna’s enhanced gain is 8.8 dB, and the rectifier’s highest RF signal to direct current conversion efficiency is 74.3%. For the combined configuration unit of measure, the antenna is assimilated into the rectifier via back-to-back 50 Ω Sub Miniature Version A (SMA) connectors. The highest recorded efficiency of 49.67% was obtained for the rectenna at optimum values of 1 kΩ resistive load and −5 dBm power input. It has been revealed that the rectifier-integrated antenna presented is effective for low-input RF energy capture and power transmission.

In this paper, a mode-matching procedure is used to prove for the first time the dispersionless behavior of glide symmetry (GS) in corrugated metasurface waveguides. Depending on their field symmetry, the Floquet harmonics have a different impact onto the frequency dispersion, which is reduced with GS when the gap between the surfaces is small. Indeed, the glide-symmetric waveguide is shown to have the same effective propagation features as a scaled mirror-symmetric waveguide with half the period and a doubled gap. We propose closed-form formulas for the effective refractive index of the glide-symmetric waveguide in the first Brillouin zone, having a small groove compared to the period. The closed-form expressions analytically prove the dispersionless behavior of GS.

The surface deformation of the main reflector in a large radio telescope is closely related to its working efficiency, which is important for some astronomical science studies. Here, we present a deep learning-based surface deformation recovery framework using non-interferometric intensity measurements as input. The recurrent convolutional neural network (RCNN) is developed to establish the inverse mapping relationship between the surface deformation of the main reflector and the intensity images at the aperture plane and at a near-field plane. Meanwhile, a physical forward propagation model is adopted to generate a large amount of data for pre-training in a computationally efficient manner. Then, the inverse mapping relationship is adjusted and improved by transfer learning using experimental data, which achieves a 15-fold reduction in the number of training image sets required, which is helpful to facilitate the practical application of deep learning in this field. In addition, the RCNN model can be trained as a denoiser, and it is robust to the axial positioning error of the measuring points. It is also promising to extend this method to the study of adaptive optics.

Single-ended and balanced 90–120 GHz microstrip power amplifier MMICs have been designed for cost-sensitive 5G and 6G backhaul in a commercial 6-inch, 0.1-µm GaAs process. At 108 GHz, measured output power is 20.4 and 22.5 dBm, respectively. At 120 GHz, measured output is 12.6 and 17.4 dBm, respectively. This is the highest reported for GaAs, among the highest reported to date for microstrip MMIC amplifiers at these frequencies and competitive with more expensive InP and GaN processes. Measurement is compared with simulation.

This paper investigates the performance of 3D-printed dielectric reflectarray antennas (RAs) with wideband behavior and beam-steering capabilities. The designed unit cell consists of a single-layer dielectric element perforated with a square hole, whose side is used to control the local variation of the reflection coefficient. The numerical analysis of the unit cell and of first $52\times52$ reflectarray working in Ka-band, whose scanning capabilities are tested just moving the feed along an arc, confirms that the unit cell has a stable behavior with respect to both the frequency and the direction of arrival of the incident field. In view of these promising capabilities, the proposed unit cell is used to design a bifocal reflectarray with the same size and working in the same frequency band of the first one. Its numerical characterization and the measurements of a prototype prove that the RA is able to provide less than 0.8 dB of gain losses over a scanning range of ±40∘ in the vertical plane, while the bandwidth varies between 13.5% and 28%, depending on the pointing direction. The obtained results demonstrate the effectiveness of the proposed approach and highlight the potential of 3D-printing technology for producing high performance, cost-effective RAs with wideband behavior and excellent beam-steering features.

Wireless power transfer (WPT) is an emerging technology with many promising applications where transmitting power via wired connections is undesirable. However, near-field WPT between magnetically coupled inductors is highly susceptible to positional changes, with power transfer efficiency (PTE) suffering if the coils are misaligned. To combat this effect, many position-independent, self-adaptive, inductive WPT schemes have been developed. Recent work indicates that it is possible to passively achieve high PTE across the operating range with nonlinear capacitors. In this work, the functionality of nonlinear WPT circuits is investigated, and fundamental design equations are derived and validated. A simplified design procedure is proposed for the position-independent self-adaptive WPT using nonlinear capacitors, wherein the ideal capacitance is extracted for each coupling factor. The efficacy of the method is demonstrated with an experimental circuit. Future work in this area is also proposed.

This work presents a passive intelligent surface designed at 2.45 GHz that has the capability of transmitting and reflecting electromagnetic waves that are incident upon it. The proposed surface does not require any circuitry or power source to function. Therefore, it makes a cost-effective and simple intelligent surface. It is a simple metallic structure that has embedded waveguide slots on its surface, allowing the waves to couple for transmission. A prototype of the proposed surface is designed using an aluminum foil and analyzed for both transmission and reflection of the wave. Further, the designed surface is investigated for tuning the directionality of the radiated field from the antenna. For this purpose, a coplanar patch antenna is first designed and then combined with the surface to tune the directionality of the radiated field of this antenna. The outcome of the measured performance validates that the proposed surface has the potential capability of field reconfiguration in wireless communication for Wi-Fi, WLAN, and Bluetooth applications.

In this paper, a low-profile antenna with characteristic of reconfigurable of dual bands’ pattern for 5G New Radio (NR) communication is proposed to mitigate the problems of signal fading and multipath propagation. The design incorporates a turnstile-shaped patch, a circular patch with etched rectangular slots and a discontinuous ring patch. The circular patch with etched rectangular slots and discontinuous ring patch are placed in the same plane to obtain dual band characteristic. The discontinuous ring patch works as a near-field resonant parasitic unit to improve the front-to-back ratio values at the resonance points and adjust the beam direction. Eight diodes are loaded to control the connection states of the rectangle slots on the circular patch. By combining an electric dipole formed by diode-controlled slot with a magnetic dipole formed by the turnstile-shaped patch, then a dual-band antenna with diverse patterns is designed. The measured results show that the designed antenna has dual-band characteristics and operates in the bands of 3.39–3.62 GHz and 4.77–5.01 GHz with peak gains of 3.6 dBi and 4.2 dBi, respectively. Furthermore, the measured radiation pattern results show that it is feasible to reconfigure the pattern in both bands simultaneously at 45° intervals.

In this paper, two second-order electronically tunable bandpass filters are presented. The filters are implemented in microstrip technology using barium–strontium–titanate (BST) varactors and digitally tunable capacitors (DTC) for tuning the frequency response of the bandpass filters. The filter realized using BST varactors has a 35% tuning range from 900 MHz to 1.275 GHz with an insertion loss variation from 3.1 to 2.6 dB. The absolute bandwidth is nearly constant over the entire tuning range, varying from 64 to 72 MHz (around ±5% variation). The filter realized using DTCs also has a 36% tuning range from 850 MHz to 1.225 GHz with an insertion loss variation from 3.1 to 1.5 dB. The absolute bandwidth is constant over the tuning range, varying from 88 to 98 MHz (around ±5% variation). The bandpass filters are tuned using a single control signal. The tunable bandpass filters are proposed for use in reconfigurable radios.

This research work presents an implantable antenna that operates at 5.8 GHz. By using a radiator with a loop-based design, the antenna can be made smaller. Radiator is made up of three connected rectangular loops. On the substrate’s back side, an I-shaped ground plane is used. As substrate and superstrate, polydimethylsiloxane (PDMS) with dimensions of 7 mm × 5 mm × 0.3 mm is used. The conducting sections are made using copper foil that is 30 µm thick. The suggested antenna is examined by the implantable medical device using realistic human scalp phantom models and a homogenous skin box. Simulated study revealed that it operates around 5.8 GHz with a bandwidth from 5.69 to 5.92 GHz. The specific absorption rate was 0.28 and 0.26 W/kg for skin box and human scalp phantoms, respectively, at 1 mW input power across 1 g volume tissue.

The design of low-profile Multiple-Input-Multiple-Output (MIMO) antennas for various 5G applications is a topic of huge interest in academia, research, and telecommunication sector. In this aspect, a compact and low-profile 5G MIMO antenna has been designed and analyzed for various 5G applications, specifically for the 24 GHz bands (24.25–24.45 GHz and 25.05–25.25 GHz) and local multipoint distribution system band (27.5–28.35 GHz) of the 5G spectrum. The proposed antenna structure is 20 × 20 × 1 mm3 in dimension. Two spade-shaped radiators composed of Copper (annealed) material are placed orthogonally to improve isolation and maintain signal diversity. Rogers RT 5880 is used as the material for substrate. The antenna exhibits a wide bandwidth of 21.5–28.5 GHz. The mutual isolation |S21| has been maintained ≤29 dB due to the insertion of a T-shaped parasitic strip in between the radiating elements. Novelty in design and superiority in performance has been observed when compared with related antenna categories.

Electronic measurement systems in the THz frequency range are often bulky and expensive devices. While some compact single-chip systems operating in the high millimeter-wave frequency range have recently been published, compact measurement systems in the low THz frequency range are still rare. The emergence of new silicon-germanium (SiGe) semiconductor technologies allow the integration of system components, like oscillators, frequency multipliers, frequency dividers, and antennas, operating in the low THz frequency range, into a compact monolithic microwave integrated circuits (MMIC), which contains most components to implement a low-cost and compact frequency-modulated continuous-wave-radar transceiver. This article presents a single transceiver solution containing all necessary components. It introduces a $0.48\,\mathrm{THz}$ radar transceiver MMIC with a tuning range of $43\,\mathrm{GHz}$ and an output power of up to $-9.4\,\mathrm{dBm}$ in the SG13G3 $130\,\mathrm{nm}$ SiGe technology by IHP. The MMIC is complemented by a dielectric lens antenna design consisting of polytetrafluoroethylene, providing up to $39.3\,\mathrm d\mathrm B\mathrm i$ of directivity and half-power beam widths of 0.95∘ in transmit and receive direction. The suppression of clutter from unwanted targets deviating from antenna boresight more than 6∘ is higher than $24.6\,\mathrm d \mathrm B$ in E- and H-Plane.

An E-band Cassegrain switched beam high-gain antenna concept for 5G backhauling systems is proposed in this article. The antenna requirements target the compensation of small misalignments (within ±1 degrees in both azimuth and elevation planes) in E-band backhauling links due to adverse weather conditions or thermal deformations. The intended antenna is able to realize beam-switching operations by using a feed-array architecture based on a 7 × 7 array of cavity-backed magnetoelectric (ME) dipoles, where every element is capable of providing a steering of ±0.33 degrees in both the elevation and the azimuth planes. The ME dipole illuminators combined with a Cassegrain reflector provide a gain of 52 dBi within the whole scanning range. Besides, they can be easily integrable with the front-end modules, thus being an easily implementable and low-cost alternative to other more complex solutions based on horns or lens antennas.

In this paper, a capsule endoscopy system with a sensing function is proposed for medical devices. A single-arm spiral antenna is designed for data transmission and is combined with the voltage controlled oscillator to achieve sensing capabilities. The designed antenna operates at a 900 MHz industrial scientific medical band. By establishing a three-layer cylindrical model of the stomach, it was concluded that the antenna in the stomach has a high peak gain of −1.1 dBi. Additionally, the antenna achieved a −10 dB impedance bandwidth of 5%. The capsule endoscopy was experimentally measured in both actual stomach and simulated environments. The maximum working distance of the capsule endoscope was measured to be 6.8 m. Additionally, the proposed capsule endoscope was tested for its sensing function using solutions with different dielectric constants. Finally, it was confirmed through link analysis that it has good communication capabilities. The results and analysis confirm that the proposed capsule endoscope can be used for examining gastric diseases.

In this study, tunability of the electromagnetically induced transparency (EIT)-like transmission window by low-volume dielectric loadings is presented both numerically and experimentally in S-band. The EIT-like transmission behavior is obtained by a metamaterial, composed of an electric resonator and a closed-ring resonator patterned on a dielectric substrate. The frequency tuning is obtained by two applications called horizontal sliding application (HSA) and vertical sliding application based on sliding of the low-volume loadings from the edges to geometric center (i.e., inward). For both applications, the frequency tuning has been investigated for dielectric loadings which have relative permittivity of 2.2, 3, 4.5, and 6.15. The results reveal that the proposed sliding applications are effective on tuning the transmission peak frequency. An achieved 1136 and 971 MHz absolute spectral shifts and corresponding 6.34% and 5.41% absolute sensitivities by simulations and measurements, respectively, are the best results which are obtained for HSA at 5 mm shift value. Moreover, 14.67% sensitivity is obtained in simulations for the complete dielectric loading on the resonator in response to the increase in refractive index from 1 to 1.5. It is believed that the proposed applications will contribute to the existent sensing studies.