A compact 12-element multiple-input multiple-output loop antenna array for a fifth-generation (5G) mobile phone is proposed. The operating band for the proposed antenna covers the long-term evolution 42 band, which spans a frequency range of 3.4–3.6 GHz. The size of the single antenna element is 5.85 × 4.9 mm2 (0.068λ0 × 0.057λ0), and 12 of these elements are positioned along two side edges of the mobile phone. This antenna is suitable for high screen-to-body ratio devices. The measured 6-dB impedance bandwidth is from 3.4 to 3.73 GHz. The measured total efficiency of the proposed antenna is 39–56% and the peak gain is 0–3.2 dBi. The transmission coefficient is less than −12 dB, the envelope correlation coefficient is less than 0.42, and the channel capacity is 45–50 bps/Hz.

Sakli et al. previously studied the propagation characteristics of wave modes in a metallic circular waveguide filled with anisotropic metamaterial [Int. J. Microw. Wirel. Technol. 9, 805–813 (2017)]. They derived and analyzed the wave equation and dispersion relations for TEz and TMz modes (i.e., TE and TM waves related to the z-axis) within the waveguide. However, they did not verify whether the system actually supports these TEz and TMz waves. This work aims to investigate that issue. Our findings indicate that, in general, a metallic circular waveguide filled with anisotropic metamaterial cannot support the propagation of TEz and TMz waves. Consequently, the results presented by Sakli et al. are incorrect.

An intra-band pattern-corrected decoupling vertical conducting wall is realized by dielectric substrate with conductor cladding on both side wall between two tightly spaced H-plane microstrip patches with λ0/20 edge-to-edge spacing. The wall is grounded and two symmetrical slots are etched on the vertical substrate. The measured results agree with the simulations, showing that the slotted vertical wall reduces the mutual coupling within the bandwidth to −30 dB and corrects the radiation beam tilt to be within −4.5° to 3° from the broadside direction. A gain reduction of 0.6 dB is observed compared to the gain without the slotted decoupling wall.

This research proposes an inexpensive technique for wireless image transfer for security and surveillance applications. The technique uses a 5.8 GHz transmitter and receiver module, along with external antennas in the real-time image transfer within a radius of 100 m. The transferred images are stored in a laptop using a Python code-based graphical user interface application. Different antennas, dipole, circular split-ring resonators, hexagonal split-ring resonators, and metamaterial antennas are utilized for comparison. The Blind/Referenceless Image Spatial Quality Evaluator method is used to assess the picture quality of transferred images to quantify image transfer performance when no ground truth or reference photos are supplied. According to the presented results, images transferred using metamaterial antennas have higher quality than those transferred with other types of antennas. For security considerations, such a system can communicate and store the images in real time.

For forthcoming wireless applications, a small and highly decoupled complementary split ring resonators (CSRR)–loaded co-planar waveguide (CPW)–fed antenna for dual-band applications is investigated. The low-profile antenna consists of a CSRR-loaded rectangular radiating element with a truncated bottom, giving a wideband performance over the frequency ranges of 5.28–5.52 GHz and 6–7.2 GHz. The antenna has been printed on a widely used FR4 substrate measuring 7.5 × 10.5 × 1.6 mm3 in volume. This research’s suggested antenna is turned into a 4 × 4 multi input multi output (MIMO) construction using a 25 × 25 mm2 printed circuit board. Individual antennas were isolated by nearly 20 dB without using a decoupling device. The antenna has been built, and the measured and simulated results correspond well. Computing envelope correlation coefficient (ECC), channel capacity (CC), and channel capacity loss (CCL) further validates the antenna’s performance (−). The antenna has an overall gain of around 2.54 dBi and a radiation efficiency of approximately 89% throughout the relevant spectral range, which is much better for wireless applications. The suggested antenna’s omnidirectional emission pattern makes it a potential contender for future wireless and cellular applications.