This paper proposes a passive filtering antenna for ultra-wideband (UWB) applications. The edge chamfering technique is adopted to construct the UWB antenna. The designed UWB antenna has a fractional bandwidth of 135%. A low-pass filter (LPF) is embedded on the feed line of the UWB antenna to convert it into a narrowband antenna that works at 2.45 GHz with 29.5% fractional bandwidth by removing the high-frequency components. The LPF is a transmission line with a stepped impedance configuration loaded with an H-shaped unit cell. The proposed filtering antenna is fabricated and tested. The measured results indicate the gain is >4.2 dBi and the radiation efficiency is >75%.

The presence of obstacles in the propagation path is a critical factor in air-to-ground (AG) communication. The behavior of wireless signal propagation depends on several variables, such as frequency, building height, elevation angle, and street design. This paper aims to compare the three established line of sight (LOS) probability model based on actual site data, including the building geometry in suburban environment. The comparison between these three models using the site data provide a guideline for selecting the LOS probability model based on the optimistic and pessimistic predictions. The shadowing loss was evaluated at frequencies 2 and 3.5 GHz with an elevation angle of 20° in two suburban locations at Universiti Tun Hussein Onn Malaysia. Three prediction models, ITU-R P.1410-5, Holis and Pechac, and Pang et al., available in the literature were used to identify and compare the line-of-sight probability. By focusing on the shadowing model in suburban area, the guideline for optimizing LOS communications or navigation in these challenging environments can be developed. The finding highlights the importance of considering building height in AG communication for network performance evaluation and design.

This article presents an ultrawide bandpass filter structure developed along a notch band using a small rectangular impedance resonator. The proposed filter structure consists of a coupled rectangular resonator (CRR), open stub, and composited split ring resonator (CSRR) at the bottom of the structure. In-band and out-of-band properties are improved by the CRR and open stub. The notch band is obtained by placing CSRR below the rectangular resonator. A filter with a compact size of 0.15 × 0.10 λg is obtained at a lowered cutoff frequency of 3.0 GHz, where λg is the corresponding guided wavelength. The proposed structure has been constructed on 5880 Rogers substrate with a thickness of 0.787 mm and a dielectric constant of 2.2. Additionally, equivalent lumped parameters were obtained, and a lumped equivalent circuit was created to explain how the suggested filter operated. The Electromagnetic (EM)-simulated results are in good agreement with the circuit-simulated and measured result. The various machine learning approaches such as artificial neural network, K-nearest neighbour, decision tree, random forest (RF), and extreme gradient boosting algorithms are applied to optimize the design, in which RF algorithms achieve more than 90% accuracy for predicting the S parameters of the ultrawideband filter.

In this paper, on–off switching digitization of a W-band variable gain power amplifier (VGPA) with above 60 dB dynamic range is introduced for large-scale phased array. Digitization techniques of on–off switching modified stacking transistors with partition are proposed to optimize configuration of control sub-cells. By the proposed techniques, gain control of a radio frequency variable gain amplifier (VGA) could be highly customized for both coarse and fine switching requirements instead of using additional digital-to-analog converters to tune the overall amplifier bias. The designed VGA in 130 nm SiGe has achieved switchable gain range from −46.4 to 20.6 dB and power range from −25.0 to 15.7 dBm at W band. The chip size of the fabricated VGPA is about 0.31 mm × 0.1 mm.

This manuscript presents a 50 Ω microstrip-fed quad-element high isolated ultra-wideband (UWB) multiple-input multiple-output (MIMO) antenna with band-notched characteristics. The overall area of the proposed structure is 0.33λo × 0.33λo mm2 (where λo depicts the free space wavelength corresponding to the lower cutoff frequency, i.e. 2.54 GHz), etched on an FR-4 substrate of thickness 0.8 mm. The top layer has four semicircular disc-shaped radiating elements that are identical and orthogonal to obtain better inter-element isolation and compactness. A reverse two-shaped slot is etched onto the radiating patches to attain a band-rejection capability. Moreover, a decoupling structure is also placed at the top layer to suppress the unwanted surface waves. The bottom layer consists of a ground plane, which is further modified with quasi-self complementary and meandered line slots. A rectangular slot is also etched below the feed line to better match the impedance near the lower cutoff frequencies. The simulated reflection coefficients (S11) of the proposed antenna are less than −10 dB over 2.54 to 10.74 GHz frequencies except at 3.37 to 4.15 GHz (WiMAX/C band), and the simulated inter-port isolation (S21) is greater than −15 dB over the entire UWB range of frequencies (3.1 to 10.6 GHz). Also, the measured S-parameter results well agreed with the simulated ones. Furthermore, the simulation study of the 20-element UWB-MIMO antenna is also investigated using the proposed quad-element structure.

In this article, the cylindrical conformation of a linearly polarized cavity-backed magnetoelectric (ME) antenna is studied. Starting from a planar ME antenna presenting a wide bandwidth due to a specific design of its feeding probe, the impact of conformation is shown; the coupling between the ME dipole and the cavity walls is demonstrated to be the key element to keep a wideband behavior. Conformal antennas offering the same impedance bandwidth as the planar antenna are presented operating at Global Navigation Satellite System frequencies (1.164–1.61 GHz). As a result of the conformation, the antenna size has to be reduced to maintain the coupling and a wideband behavior. A prototype conformed to a 44-mm radius cylinder was built using low-cost additive manufacturing. External dimensions of 62 × 62 × 35 mm3 (0.285 × 0.285 × 0.16λ03, where λ0 is the wavelength at 1.38 GHz) were obtained, showing a ground plane area reduction of 46% compared to the planar antenna with the same materials. The conformal antenna also exhibits very steady radiation properties with a gain of around 4.5 dBi and a very similar and stable 3 dB beamwidth around 113° in E- and H-planes. A relatively good agreement is found between measurements and simulation.

This article presents an innovative design for a low-profile, high-gain circularly polarized (CP) antenna using a single-layer metasurface (MTS). The proposed design incorporates an MTS layer, comprising a 4 × 4 array of hexagonal-shaped patches, printed on the top layer of the substrate. The bottom layer features a coplanar waveguide-fed slotted ground. Circular polarization and broadside radiation are achieved through the application of characteristic mode analysis (CMA). CMA is employed to simultaneously excite desired modes, aiming for wideband circular polarization and gain enhancement. Experimental results validate the effectiveness of the design, with compact dimensions of 0.67λ0 × 0.67λ0 × 0.04λ0. The measurements demonstrate an impressive impedance bandwidth of 84.3% within the 3.7–9.1 GHz. Additionally, a 3-dB axial ratio bandwidth of 18.6% is observed between 4.96 and 5.98 GHz and 3.74% between 8.38 and 8.7 GHz. The antenna exhibits excellent radiation pattern characteristics, featuring a maximum gain of 10.08 dBi at 7.1 GHz. The radiation pattern is symmetrical with broadside directionality, making the antenna well-suited for sensing applications.

In this paper, a novel dual-mode spherical resonator is proposed. By rotating the coupling irises, perturbations are generated to split the degenerate modes. The proposed filter is cascaded by a dual-mode resonator and two single-mode resonators, which are placed in a rotary way. Four poles appear in three resonators by only changing the rotation angle (φ) without any additional design. It forms the BSCT, generating a transmission zero (TZ) at the upper stopband. Furthermore, by adjusting φ further, the CT coupling topology can be obtained, resulting in a TZ at the lower stopband. Finally, slots are etched on the surface of the resonators for spurious response suppression. With the above methods, the out-of-band selectivity and suppression are greatly improved. For the fast validation, the filter is 3-D printed and measured. As a result, the measured results match well with the simulated ones.

Future smart reconfigurable antennas (RAs) (Haupt R-L and Lanagan M (2013) Reconfigurable antennas. IEEE Antennas and Propagation Magazine 55, 49–61) will likely be fully multipurpose and controlled by software and equipped with machine learning skills that can discern and respond to alterations in the radio frequency environment. Cognitive radio utilizations will be accomplished using a new generation of antenna technology and communication protocols. The effective use of frequencies and the use of polarization diversity and radiation pattern reconfigurability to send data over existing congested frequencies will be major advantages for such applications. The usage of antennas that can be reconfigured in multiple-input multiple-output (MIMO) channels will enhance channel capacity while simultaneously improving channel efficiency and lowering costs (Christodoulou C-G, Tawk Y, Lane S-A and Erwin S-R (2012) Reconfigurable antennas for wireless and space applications. Proceedings of the IEEE 100, 2250–2261). There are a lot of antennas used both at the transmitter and at the receiver front end in a MIMO system. The benefit of employing such arrangements is that different types of information can be conveyed at a similar time, boosting the spectral efficiency of communication in a multipath situation. The coding rate, modulation level, and transmission signaling method of a MIMO system can all be changed in response to changing channel circumstances and user needs. In a MIMO context, polarization reconfigurable/frequency-reconfigurable/radiation pattern RA increase the degree of freedom and enhancing the system’s performance. The usage of such antennas greatly enhances capacity by enabling a choice of various polarization configurations and pattern diversity. Antenna arrays that can be reconfigured are also an appealing MIMO system solution that needs to retain robust communication channels, particularly in portable gadgets where the area is limited.

An ultra-wideband current-reused low-noise amplifier (LNA) monolithic microwave integrated circuit design is presented in this letter. Negative feedback networks are employed at both stages of the proposed LNA to expand bandwidth. Furthermore, source adaptive bias networks is designed in the first stage and combined with a current-reused construction to acquire a compact chip size and maintain low power consumption. Then, the validation of design theory is implemented by employing a 0.15-µm gallium arsenide pseudomorphic high-electron-mobility transistor process. The measured results show that the proposed LNA achieves a small signal gain of 15.5–17.8 dB, a noise figure of 3–3.65 dB, and an output 1 dB compression point (OP1 dB) of 14.5–15.5 dBm from the target bandwidth of 2–18 GHz. In addition, the fabricated LNA consumes 220 mW from a 5 V supply and occupies a chip area of 1.2 × 1.5 mm2.

A multi-band circularly polarized antenna is proposed for WLAN (2.4/5.3/5.8 GHz) and WiMAX (3.5 GHz) applications. The proposed antenna is constructed of a radiation patch and a reflecting metal ground. Characteristic mode theory is utilized to analyze the modes of the patch and based on these results the antenna is optimized. The −10 dB impedance bandwidths of the proposed antenna are 53.53% (2.4–4.15 GHz) and 47.28% (5.25–8.5 GHz), respectively. The antenna radiates left-handed circular polarization in the lower band and right-handed circular polarization in the upper band. A maximum gain of 10 dBic is achieved for the proposed antenna.

Circular antenna array (CAA) is one of the most widely used antenna array designs. This paper addresses the design challenges of the CAA with the non-uniform single ring, which is placed in an X-Y plane with the best sidelobe level (SLL) and improved first null beamwidth (FNBW). It has been solved using differential evolution, craziness-based particle swarm optimization (CRPSO), and novel particle swarm optimization (NPSO) techniques. An optimal combination of feeding current and inter-element spacing provides an array pattern with the best SLL and improved FNBW, as well as some other parameter calculations of the antenna array like maximum directivity, maximum effective aperture, total effective aperture, maximum beam area, total beam area, circumference, and radius of the CAAs using these techniques. There are six designs of CAAs with different antenna elements (i.e., 10-, 12-, 16-, 20-, 36-, and 64-elements) which have been taken into account. Simulations are done in MATLAB. Based on various simulation results, we can analyze the performance of SLL and FNBW with other parameters using NPSO and compare them with different techniques of CAAs, as shown in the numerical analysis and simulation result section.

In this paper, a radio frequency sensor for measuring microfluidics dielectric properties is designed based on microstrip meander line. The meander sensor replaces the straight transmission lines with meander transmission lines in the part of the half-wavelength path difference to improve the sensitivity of the sensor and reduce its size. According to the experimental results, the meander sensor based on the meander line has higher accuracy and a lower relative error than the straight sensor in measuring methanol–ethanol mixtures with different molar fractions. The relative error measured by the meander sensor after calibration with an adjustable cavity is less than 1%. It is easier to detect the very slight variation in dielectric properties brought about by microfluidics. The detection technique can be further applied for the accurate detection of dielectric properties of valuable biological samples, providing a more concise and convenient way.

For future fifth-generation (5G) smartphones, a high-efficiency multiple-input/multiple-output (MIMO) antenna system capable of operating in Long Term Evolution (LTE) 42/43/46 is suggested. A pair of small microstrip-fed slot antenna and inverted F antenna is part of the single antenna design structure. They are positioned on the longer side of the FR-4 printed circuit board. In an effort to lessen the mutual coupling, two antenna elements have a U-shaped rectangular slot inserted between them. The detailed study of the suggested MIMO system includes measurement of the reflection parameter, analyzing the radiation performance, performing envelope correlation coefficient (ECC) and channel capacity calculations, and analyses of the effects of user’s hand in the vicinity of the antenna array. Simulation and measurement results demonstrate the required performance of the proposed design, that is, greater than 80% of total efficiency, isolation >12 dB, and ECC <0.15. The suggested antenna has the benefits of multiband operation, high efficiency, good isolation, and a small footprint.

This paper presents a broadband circularly polarized (CP) antenna array for millimeter-wave applications, and the antenna array has the advantages of wide impedance bandwidth (IBW), novel CP design, and low profile. The antenna unit consists of a two-layer substrate and two pairs of magnetoelectric dipoles. Stepped microstrip lines coupled by rectangular slits form a feeder network for easy integration. The axial ratio bandwidth (ARBW) is extended because a pair of parasitic patches is loaded and an elliptical perturbation is added. The simulation results show that the antenna has an ARBW of 18.6% (26.4–31.9 GHz) and an IBW of 45.5% (20.6–32.7 GHz), with a gain greater than 7.11 dBic in the IBW. To improve the gain of the antenna, a 2 × 2 antenna array is designed, fabricated, and measured. The measured results show that the array has an ARBW of 16.6% (26.42–31.21 GHz), an IBW of 41.6% (22.28–33.97 GHz), a peak gain of 13.89 dBic in the IBW, the cross-polarization levels in the xoz-plane and yoz-plane are above 20 dB, and a radiation efficiency greater than 89%.

This paper introduces a tri-band stacked elliptical patch antenna featuring a right-handed circular polarized, designed to operate at the L2, L5, and L1 Global Navigation Satellite System bands. Initially, an elliptic patch is constructed and fed by a probe feed to generate TM110 and TM210 modes at resonance frequencies calculated using Mathieu functions. The probe position is precisely adjusted to excite the quasi-orthogonal mode of TM110 to generate circularly polarized (CP) waves at the L2 and L5 bands. Subsequently, an eye-shaped aperture is engraved into the elliptical patch to enhance the axial ratio (AR) beamwidth in the L2 and L5 bands and stimulate the orthogonal mode of TM210 to produce CP waves at the L1 band. Lastly, a stacked partially elliptical parasitic element is placed beneath the upper slotted elliptical patch to enhance the orthogonality of TM210 surface current versions and thus improve the AR beamwidth at the L1 band. The proposed antenna shows low reflection coefficient values at 1.12–1.33 (L2/L5), and 1.5–1.66 GHz (L1). The AR beamwidths are 133/213∘, 167/163∘, and 36/103∘ at two orthogonal cutplanes at L5, L2, and L1 bands, respectively. The antenna also has decent gains of 6–6.9 dBic across the three bands.

This article presents a dual-band planar microwave sensor to characterize the permittivity of liquid samples. The sensor utilizes a splitter–combiner microstrip segment loaded with two pairs of triangular-shaped complementary split-ring resonators (CSRRs). By integrating a meander slot into the CSRRs and incorporating inter-resonator coupling between the CSRRs, the proposed sensor achieves enhanced frequency shifts, resulting in improved sensitivity. An adulteration detection experiment is conducted to validate the sensor’s performance by mixing mineral oil into castor oil with a polydimethylsiloxane container placed on the sensing area. The variations in resonant frequency and peak attenuation are employed to extract the permittivity of the loaded liquid sample. The peak sensitivities in determining the real permittivity are measured to be 6.34% and 5.7% for the first and second frequency bands, respectively. The measured errors for extracting the real and imaginary parts of the complex permittivity are approximately 3.95% and 7.47% for the first frequency band and 3.67% and 6.28% for the second frequency band, respectively. The proposed dual-band microwave sensor, with its high sensitivity, compact size, small sample volume, and low cost, demonstrates great potential for applications in the quality monitoring of agricultural and industrial products.

In this study, a high-isolation multiple-input multiple-output (MIMO) microstrip patch antenna (MPA), which utilizes an orthogonal mode cancellation method is proposed. This method employs TM10 and TM01 modes, which are simultaneously excited in the rectangular passive MPA. Initially, a rectangular decoupling structure featuring polarization rotation characteristics is designed. Further studies show that by loading the polarization conversion parasitic structure (PCPS), the electric field of the spatial coupling wave can be transformed from the x-polarized TM10 mode to the y-polarized TM01 mode. Therefore, TM10 and TM01 modes from the excited antenna and decoupling structure are concurrently coupled to the passive antenna, forming an evident weak-field region on the passive antenna. Placing the feeding probe of the passive MPA within the weak-field region prevents signal reception at the port. Consequently, this results in an extremely low mutual coupling of −49 dB at a resonant frequency of 5.8 GHz. Finally, a prototype of the proposed antenna is fabricated and tested, and the measured results closely match the simulated results. Additionally, it is observed that PCPS slightly influences the performance of the MIMO antenna.

This research article proposes a dual-sense dual-port wideband circularly polarized (CP) multi-input multi-output (MIMO) antenna designed for Wi-Fi 6E applications. The main novelty lies in achieving CP for both ports using a truncated rectangular-shaped aperture. By incorporating design and spatial diversity and defective ground structure between the two radiators, the design improves isolation and enables the antenna to generate Left-Hand Circular Polarization (LHCP)depending on the selected feed port. The proposed MIMO rectangular dielectric resonator antenna demonstrates an impressive impedance-matching bandwidth (IBW)from 5.5 to 8.0 GHz (37.10%) as well as an axial ratio bandwidth (ARBW) covering from 6.0 to 6.55 GHz (12.20%). Additionally, the dual-port wideband CP MIMO antenna exhibits satisfactory diversity performance parameters. To validate the simulated results, a physical prototype is fabricated and subjected to experimental testing. The measured outcomes of the fabricated model align closely with the simulated results, confirming the accuracy of the design. With both MIMO and CP capabilities and improved isolation, this proposed model proves beneficial in reducing latency and minimizing the impact of multipath fading. Therefore, it stands as an excellent choice for future devices utilizing the Wi-Fi 6E band due to its broad IBW and overlappingAR.