We present the idea of intensified attosecond X-ray generation based on nonlinear Thomson backscattering of an intense laser pulse by electrons trapped in plasma-vacuum boundary. Two frequency up-conversions due to the relativistic Doppler effect and longitudinal γ-spike effect are analyzed, respectively, where γ is the relativistic factor of the plasma surface. Relativistic resonance heating conditions should be used as a criterion for the experimental design to obtain efficient high-order harmonics and energetic electrons' generation at relatively low laser intensities. Shaping the laser field by proposing a detuned second-harmonic can generate a single attosecond pulse without spectral filtering.

Linear transformer driver (LTD) technology is actively developed at the Institute of High Current Electronics in Tomsk, Russia. This technology is being examined for use in high current high voltage pulsed accelerators. Recent development of high voltage low inductance capacitors and low inductance switches enabled to achieve ~100 ns rise time of the LTD output pulse. This technique allows one to eliminate intermediate pulse forming sections, used in the present accelerator technology, which would keep the footprint of an LTD accelerator small. LTD based drivers are currently considered for many applications, including future very high current Z-pinch drivers for inertial confinement fusion, medium current drivers with adjustable pulse length for isentropic compression experiments, and finally relatively low current accelerators for radiography and X-pinches. In this article, we present the design and test results for a new LTD stage, that operates at 100 kV charging voltage. Current amplitude up to 850 kA with ~140 ns rise time was obtained on a 0.05 Ω load. Stack of the LTD stages can be easily assembled in series or in parallel, thus providing voltage or current multiplication, respectively. Design of multi-mega-volt and multi-mega-ampere generators becomes straightforward with the LTD technology.

The high energy loss of heavy ions in matter as well as the small angular scattering makes heavy ion beams an excellent tool to produce almost cylindrical and homogeneously excited volumes in matter. This aspect can be used to pump short wavelength lasers. For the first time, a beam of heavy ions was used to pump a short wavelength gas laser in an experiment performed at the GSI ion accelerator facility in December 2005. In this experiment, the well-known KrF* excimer laser was pumped with an intense uranium beam. Pulses of an uranium beam compressed down to 110 ns (full width at half maximum) with initial particle energy of 250 MeV per nucleon were stopped inside a gas laser cell. A mixture of an excimer laser premix gas (95.5%Kr + 0.5%F2) and a buffer gas (Ar) in different proportions was used as the laser gas. The maximum beam intensity reached in the experiment was 2.5 × 109 particles per pulse, which resulted in 34 J/g specific energy deposited in the laser gas. The laser effect on the transition at λ = 248 nm has been successfully demonstrated by various independent methods. There, the laser threshold was reached with a beam intensity of 1.2 × 109 particles per pulse, and the energy of the laser pulse of about 2 mJ was measured for an ion beam intensity of 2 × 109 particles per pulse. As a next step, it is planned to reduce the laser wavelength down to the vacuum ultraviolet spectral region, and to proceed to the excimer lasers of the pure rare gases. The perspectives for such experiments are discussed and the detailed estimations for Xe and Kr cases are given. We believe that the use of heavy ion beams as a pumping source may lead to new pumping schemes on the higher lying level transitions and considerably shorter wavelengths, which rely on the high cross sections for multiple ionization of the target species.

The minimum irradiance needed to overcome amplified spontaneous emission (ASE) of a seed beam injected into a laser amplifier is evaluated. The treatment is particularly applicable to extreme ultraviolet (EUV) and X-ray laser schemes to inject laser harmonic radiation as a seed into (1) plasma laser amplifiers and (2) free-electron lasers. Simple expressions and calculations are given for the minimum injected irradiance required for amplification of the injected seed beam to exceed ASE from the amplifier, including the effects of gain saturation, assuming one dimensional radiative transfer.

The theoretical description of the energy loss of heavy ions in fully ionized matter is considered, where we focus on the many–body and plasma physics aspects of the stopping of point like projectiles with a fixed charge by free electrons, disregarding the atomic physics of the projectile and the target ions. This starts by identifying different coupling regimes for a heavy ion which passes through an electron plasma, and continues with a discussion of the available and appropriate analytical and numerical treatments of the energy loss and their applicability in these various regimes. Special attention is given to a nonlinear coupling regime with significant strong coupling effects on the projectile-target energy transfer where standard perturbative approaches cease to be valid. More advanced theoretical treatments, which are required for this regime, are presented, discussed and evaluated by comparison with simulation results.

Recent experimental results demonstrated that well formed plasma jets can be produced at laser interaction with targets made of materials with high atomic number (A ≥ 29 where A = 29 corresponds to Cu). On the contrary, it is impossible to launch a plasma jet on low-A material targets like plastic. This paper is aimed at explanation of this difference by considering mechanisms responsible for plasma jet formation, i.e., the radiative cooling of ablative plasma and the influence of target irradiation annular profile speculated hitherto, newly complemented by different expansion regimes of the Cu and plastic plasmas (provided by numerical simulations). The experiment was carried out with the PALS iodine laser. Two different planar massive targets, plastic and Cu, as well as the plastic target covered by thin Cu layers of various thicknesses were irradiated by the third harmonic laser beam of energy of 30 J, pulse duration of 250 ps (full width at half maximum), and the focal spot radius of 400 µm. To find the most suitable range of these layers (from 28 to 190 nm) a simple analytical model of laser-driven evaporation was developed. Three-frame laser interferometer and an X-ray streak camera were used as two main diagnostic tools. Numerical modeling was performed with the use of two-dimensional hydrodynamic code ATLANT-HE. Results provided from experiments and theoretical analyses have proved that the process of plasma jet formation is rather complex. Relative importance of the three mechanisms mentioned above depends on the target irradiation geometry as well as the target material used.

This article presents the resonant excitation of the upper hybrid wave (UHW) by cross focusing of two high power laser beams in a collisionless hot magnetoplasma; taking into account the relativistic nonlinearity. The electric vectors of the two beams are polarized along uniform static magnetic field and the beams propagate perpendicular to the static magnetic field. The resonant excitation of the UHW occurs when the frequency difference (FD) of the two laser beams and difference of their propagation vector satisfy the dispersion relation corresponding to the UHW. It has been observed that the power associated with the excited UHW, which depends on the background electron concentration, magnetic field and the intensity of the two laser beams, becomes drastically modified with the distance of propagation. The effect of the excited UHW at the FD on the acceleration of electrons has also been discussed. The amplitude of the UHW, excited by two high power laser beams and the electron energy are also calculated. This study is relevant in heating of plasma near the upper hybrid frequency as well as electron acceleration. The results are presented for typical laser plasma parameters.

The rise-time of the pulse on the diode of the intense electron-beam accelerators (IEBA) is one of the important factors that affect the quality and characteristic of the output beam current of the IEBA. In this paper, effect of the transition section between the main switch and middle cylinder of strip spiral Blumlein line (SSBL) on the diode voltage of IEBA is analyzed in theory, based on the theoretical analysis of the wave propagation along the Blumlein pulse forming line (BPFL), the traveling time of the transition section has a great effect on the rise-time, the plateau-time, and the fall-time of the output voltage at the matching load. Furthermore, the operation of the whole accelerator consisting of the primary energy-storage capacitor, the Tesla transformer, a main switch, the transition section, BPFL, and a resistive load was simulated using a circuit-simulation code called PSpice, and the dependence of the output voltage on the inductance of the main switch and the transition section was obtained. It was found from the wave propagation theory and the circuit simulation using computer results that the wave traveling time of the transition section between the main switch and the middle cylinder of the SSBL influences considerably the rise-time, plateau-time, and fall-time of the voltage waveform at the matching load. In order to get an ideal square pulse voltage waveform at the matching load and to improve the electron beam quality of such an accelerator, the wave traveling time of the transition section should be designed as soon as possible. At last, a couple of contrastive experiments are performed on two kinds of IEBA. The experimental results agree with the theoretical analysis and simulated results.

Ion acceleration by short, high intensity laser pulses in sets of small targets is treated by an analytical model developed here, and by two-dimensional particle-in-cell simulations. When an intense short laser pulse illuminates a thin foil target at normal incidence, electrons in the target are accelerated by the ponderomotive force. At the rear surface of the foil they generate a strong electric field that accelerates the ions, and generates an ion beam of small divergence. Using a mass-limited small target like a droplet enhances the ion energy, but increases divergence at the same time. In this paper, a combination of several-micron targets in a periodic structure (for example, a droplet chain) is proposed in order to increase the conversion efficiency from the incident laser beam to the emergent protons. Improvement of the energy flux conversion efficiency from the laser to the ion beam at optimal conditions is demonstrated.

The presence of an axial magnetic field in a laser beat wave accelerator enhances the oscillatory velocity of electrons due to cyclotron resonance effect leading to higher amplitude of the ponderomotive force driven plasma wave, and higher energy of accelerating electrons. The axial magnetic field inhibits the transverse escape of electrons and thus causes a growth of the interaction length. The surfatron acceleration of electrons also shows a similar enhancement. A surfatron transverse magnetic field deflects the electrons parallel to the phase fronts of the accelerating wave keeping them in phase with it. However, the electron continues to move away radially.

We will theoretically and experimentally study the effect of the linewidth and the frequency of a weak detuned signal on its amplified spectrum in the Brillouin amplifier. We will show that the spectral profile of the input signal is preserved during amplification only when the signal linewidth is much narrower than the Brillouin linewidth of the amplifier. If the signal linewidth is near or above the Brillouin linewidth, the frequency shift of the amplified signal with respect to the pump will be close to the Brillouin shift of the amplifier, and will be independent of the frequency shift of the input signal.

A two-layer target irradiated by an intense laser to generate strong interface magnetic field is proposed. The mechanism is analyzed through a simply physical model and investigated by two-dimensional particle-in-cell simulation. The effect of laser intensity on the resulting magnetic field strength is also studied. It is found that the magnetic field can reach up to several ten megagauss for laser intensity at 1019 Wcm−2.

The Large Hadron Collider (LHC) will operate with 7 TeV/c protons with a luminosity of 1034 cm−2 s−1. This requires two beams, each with 2808 bunches. The nominal intensity per bunch is 1.15 × 1011 protons and the total energy stored in each beam is 362 MJ. In previous papers, the mechanisms causing equipment damage in case of a failure of the machine protection system was discussed, assuming that the entire beam is deflected onto a copper target. Another failure scenario is the deflection of beam, or part of it, into carbon material. Carbon collimators and beam absorbers are installed in many locations around the LHC close to the beam, since carbon is the material that is most suitable to absorb the beam energy without being damaged. In case of a failure, it is very likely that such absorbers are hit first, for example, when the beam is accidentally deflected. Some type of failures needs to be anticipated, such as accidental firing of injection and extraction kicker magnets leading to a wrong deflection of a few bunches. Protection of LHC equipment relies on the capture of wrongly deflected bunches with beam absorbers that are positioned close to the beam. For maximum robustness, the absorbers jaws are made out of carbon materials. It has been demonstrated experimentally and theoretically that carbon survives the impact of a few bunches expected for such failures. However, beam absorbers are not designed for major failures in the protection system, such as the beam dump kicker deflecting the entire beam by a wrong angle. Since beam absorbers are closest to the beam, it is likely that they are hit first in any case of accidental beam loss. In the present paper we present numerical simulations using carbon as target material in order to estimate the damage caused to carbon absorbers in case of major beam impact.

Monoenegetic ion beam generation from circularly polarized laser-pulse interaction with a double-layer target is considered. The front layer consists of heavy-ion plasma, and the rear layer is a small thin coating of light-ion plasma. Particle-in-cell simulation shows that the multi-dimensional effects in the ion radiation pressure acceleration are avoided and a highly monoenergetic light-ion beam can be produced. Our simulations reveal that the charge-mass ratio of heavy ions in the front layer and the thicknesses of both layers can strongly affect the proton energy spectra.

Energy production by laser driven fusion energy is highly matured by spherical compression and ignition of deuterium-tritium (DT) fuel. An alternative scheme is the fast ignition where petawatt (PW)-picosecond (ps) laser pulses are used. A significant anomaly was measured and theoretically analyzed with very clean PW-ps laser pulses for avoiding relativistic self focusing. This permits a come-back of the side-on ignition scheme of uncompressed solid DT, which is in essential contrast to the spherical compression scheme. The conditions of side-on ignition thresholds needed exorbitantly high energy flux densities E*. These conditions are now in reach by using PW-ps laser pulses to verify side-on ignition for DT. Generalizing this to side-on igniting solid state density proton-Boron-11 (HB11) arrives at the surprising result that this is one order of magnitude more difficult than the DT fusion. This is in contrast to the well known impossibility of igniting HB11 by spherical laser compression and may offer fusion energy production with exclusion of neutron generation and nuclear radiation effects with a minimum of heat pollution in power stations and application for long mission space propulsion.

This paper, based on a relativistic electron-beam accelerator with inductive energy accumulation, investigates the layer structure, plasma jet, and thermal dynamics of Cu target under the irradiation of pulsed electron beam (~350 kV, ~4 kA, ~300 ns). A description of a relativistic electron beam source with a carbon fiber cathode is presented. After the electron-beam irradiation at ~13 J/cm2 energy density, microcraters with 0.5–1 µm diameter appeared on the target surface, and the target cross section is characterized by multilayer structures with a ~20 µm thickness melting layer and a cellular layer. Further, it was found that the carbon content increased significantly not only on the target surface but also on the cross section. The gas liberation per pulse induced by electron beam is analyzed. A good agreement between the experimental and calculated perveances was observed, with the exception at the end of the accelerating pulse possibly due to the participation of ion flow from the anode target. In the pulsed emission, there existed material transfer from anode to cathode, which is observed by the identification of elemental compositions on cathode surface. As the beam energy is deposited on target surface, the anode plasma jet is generated, and expands toward the cathode at a velocity of ~3 cm/μs. By solving the one-dimensional heat equation, 109 K/s heating rate and 107 K/m temperature gradient can be obtained. After the heating of pulsed electron beam, the thermal conduction is dominant, with a cooling rate on the order of 107 K/s. The relativistic electron beam sources may provide a potential development for target experiments and high energy density physics.

The development of pulsed power technology, particularly for inductive energy storage, promotes the extensive discussions of electrical explosion process in high energy density. This paper presents the electrical-explosion behavior of carbon fibers subjected to about 20 kA, ~5 µs high-density current pulse igniting an intense electron beam accelerator. After electrical explosion, and surface rupture, submicron particles, fibrillar and strip-shaped structures were observed, experimentally supporting the microstructure model (skin-core heterogeneity) of carbon fiber. Interestingly, the start and turn-off of the current were followed by radiation pulses with different intensities. It was found that the radiation was focused on the explosion stage which was characterized by an oscillating current. The instabilities of plasma produced during the explosion process play an important role in the microstructure changes of carbon fibers and the radiation generation.

A laser direct writing technique was used successfully to carry out subsurface micromachining of three-dimensional microfluidic structures. It involves simple steps of femtosecond laser irradiation to project a latent image of channels or chambers of various dimensions into a photosensitive Foturan glass, thermal annealing to produce crystallites of lithium metasilicates in the laser-irradiated regions, and use of a diluted hydrofluoric acid solution to remove the crystallized structures through selective chemical etching. The etched surfaces may be smoothened significantly through a secondary thermal annealing process. A microfluidic reagent mixer and reactor consisting of four cubic chambers and multiple channels was produced inside a single piece of glass to demonstrate that the technique can be used for rapid device fabrication without recourse to the cumbersome and expensive processes of alignment, stacking, bonding or assembly of the individual microcomponents. The direct writing technique makes it easy to integrate micro–optical and microfluidic components into a single chip.

Clusters of condensed deuterium of densities up to 1029 cm−3 in pores in solid oxide crystals were confirmed from time-of-flight mass spectrometry measurements. Based on these facts, a schematic outline and possible conclusions of expectable generalizations are presented, which may lead to a simplification of laser driven fusion energy including new techniques for preparation of targets for application in experiments of the NIF type, but also for modified fast igniter experiments using proton or electron beams or side-on ignition of low compressed solid fusion fuel.