The effect of heat treatments on the total charge and water adsorption by Ca-, Na- and Li-saturated kaolinite was studied using extraction techniques and thermal gravimetric analysis, respectively. Measurements of cation exchange capacity indicated that the total charge of Li-kaolinite was reduced by approximately 50% after heating to 110 or 130°C. In contrast, the total charge of Ca-kaolinite remained essentially constant while that of Na-kaolinite decreased slightly. Water adsorption and desorption on Ca- and Li-kaolinite following heat treatments at 150°C were consistent with the total charge of the respective kaolinites. Ion extraction of Li-kaolinite using NH4C1 revealed that only 6% of the Li remained exchangeable after heating, while Al and H were released. Thus, non-exchangeable Li ions not only reduced the total charge of the kaolinite but also displaced Al and H from the kaolinite structure. Infrared spectroscopy also indicated that Li migrated into the kaolinite structure and replaced a portion of the Al from the octahedral sheet. The results presented here indicate that Li-kaolinite represents a surface of reduced charge rather than a surface free of cation-hydration effects. Therefore, Li-kaolinite is not recommended as a reference for the study of vapor-phase adsorption, and conclusions based on such a reference material should be reevaluated.

A procedure for the determination of cation exchange capacity (CEC) and the amounts of exchangeable cations adsorbed to montmorillonite is proposed. The method consists of a single incubation of the clay in a suspension containing a low concentration of an organic dye of large binding affinity, followed by analysis of the displaced inorganic cations by inductively-coupled plasma emission spectrometry (ICPES). The CEC is obtained by taking the largest sum of displaced exchangeable cations. Montmorillonite suspensions were incubated with methylene blue (MB) or crystal violet (CV) at dye concentrations below 4 mM, for one, three or fourteen days. For total dye concentrations up to the CEC, all the dye was adsorbed and equivalent amounts of exchangeable cations were released. Both dyes could adsorb to the clay in excess of the CEC.

After one day of incubation in the presence of dye concentrations of about 50% in excess of the CEC, the total amounts of cations released were reduced to below the CEC. This reduction was interpreted as due to massive aggregation of the clay particles induced by the dye. With CV the total amounts of cations released after three or fourteen days of incubation increased and became equal to the CEC.

The same CEC was found for Na-, Ca- and SWy1 crude-montmorillonite, by employing either of the dyes.

A series of reduced-charge (RC) hectorites were prepared by multiple heat (250°C) treatments of Mg-saturated hectorites (SHCa-1 ). Cation exchange capacity (CEC) measurements and alkylammonium exchange indicated that a decrease in layer charge occurred with each Mg-250 treatment. Chemical analyses showed that decreases in structural Li and increases in structural Mg contents coincided with charge reduction. Fluorescence measurements of adsorbed quinoline indicated that the hectorite surface was acidified during charge reduction; hydroxyl group deprotonation is a possible source for the acidity. Fourier transform infrared spectra (FTIR) indicated that the Mg-250 treatment induced the loss of structural Li and shifted the SiO stretch band to a position similar to that in talc. The relative intensities of the OH and SiO stretch bands in FTIR spectra suggest that some of the hydroxyl groups in hectorite were lost, possibly by deprotonation. However, thermogravimetric data (TG) reveal no significant difference in the hydroxyl contents of the hectorites.

The FTIR spectra, CEC, layer charge, chemical, and TG data all supported the view that Mg substitution for octahedral Li occurred which resulted in a more “talc-like” structure. Charge reduction in smectites is evidently a general phenomenon and can be induced by heat treatment with the proper exchangeable cation. The ability to reduce the charge of hectorites makes it possible to prepare a series of clays which vary in charge but lack structural Fe. Such RC smectites should be suitable for expandable clay mineral studies which utilize spectroscopic techniques that are sensitive to Fe content.

Experimental cation exchange capacities (CEC) of kaolinites were determined and compared to theoretical calculations of CEC. The comparison reveals that the exchangeable cations occur mostly on the edges and on the basal (OH) surfaces of the mineral. It also shows that permanent negative charge from isomorphous substitution of Al3+ for Si4+ is insignificant. The CEC of kaolinite strongly depends on the particle size (both thickness and diameter in the (00l plane) and pH value. Particle size is more important than crystallinity in affecting kaolinite CEC. This study shows that the hydroxyls on the exposed basal surfaces may be ionizable in aqueous solutions. The amount of negative charge on the edges and the exposed basal hydroxyls depends on pH and other ion concentrations. A higher pH value gives rise to more negative charges, which lead to a higher CEC value. This study indicates that charge from broken edges and exposed OH planes rather than charge from Al/Si substitution determines the kaolinite CEC, even at zero point charge. A high CEC in some kaolinites is found to be due to smectite layers on the surface of the kaolinite crystals.

The objective of this work was to prepare series of reduced-charge materials from different parent Li-saturated dioctahedral smectites, to investigate the effects of temperature, chemical composition and charge location in smectites on the charge reduction and to characterize reduced-charge smectites (RCSs) using methylene blue (MB) adsorption. The layer charge decrease, induced by Li fixation, is correlated with the trends in the spectra of MB-RCS dispersions in the visible region (VIS) spectra. Distribution of the negative surface charge of the clay minerals controls the distance between the adsorbed MB cations and thus affects the formation of MB dimers and higher agglomerates. Because each form of MB (monomer, dimer, higher agglomerate, J-aggregates) absorbs light at a different wavelength, the VIS spectra of MB depend sensitively on the charge density at the clay surface. Both cation exchange capacity (CEC) values and spectra of MB-clay dispersions clearly detect extensive reduction of the layer-charge density in reduced-charge montmorillonites (RCMs) upon Li-thermal treatment. The extent of charge reduction depends on the temperature of the thermal treatment, as well as on the octahedral charge of the montmorillonite. Reduction of the layer charge proceeds to a much lesser extent for smectites with mainly tetrahedral charge and high Fe content (Fe-rich beidellite and ferruginous smectite). Both CEC data and MB spectra detect only a slight decrease of the layer charge density, which relates to the low octahedral charge of these minerals. Following heating at higher temperatures (120-160°C), slightly higher Li fixation is indicated by CEC values; however, no charge reduction is confirmed by MB spectra. Release of protons accompanying Li+ fixation in Fe-rich smectites heated at 180 or 200°C was detected in the spectra of MB-clay dispersions and confirmed by potentiometric titrations.

The uptake of Sr and Cs by 2 types of aluminum pillared layered clays (Al-PILC), a reference sample (AZA) and a specially tailored sample (FRAZA), were investigated. The AZA sample was prepared from air-dried precursors and the FRAZA sample from freeze-dried precursors. X-ray diffraction (XRD), pore and grain size measurements revealed that freeze-drying leads to a very fine-grained material with substantial mesoporosity. In contrast, air-drying results in coarse grains and an essentially microporous material. Four different methods were tested for restoring the cation exchange capacity (CEC) of the prepared PILCs. The most effective method proved to be exposing the material to ammonia fumes, then soaking it in a NaCl solution at pH =10. Strontium and Cs kinetic experiments were carried out with PILCs after restoring their CEC by this method. The results revealed 1 fast uptake component in both materials but with different relaxation times for each PILC.

Hisingerite, first described in 1810, has been variously regarded as noncrystalline, as a septechlorite, as ferric allophane, as ferric halloysite and as poorly crystalline nontronite. Hisingerite from the original localities of Gillinge and Riddarhyttan in Sweden has a composition close to Fe2O3·2SiO22H2O. X-ray diffraction (XRD) analysis of Riddarhyttan hisingerite yields very broad maxima at 7.7, 4.44, 3.57, 2.56, 2.26, 1.69 and 1.54 Å, and that from Gillinge is similar. Cation exchange capacities are 2.2 meq/100 g (Riddarhyttan) and zero (Gillinge). Transmission electron microscopy (TEM) shows a fabric of concentric spheres and part spheres, with diameters of about 140 Å and walls up to six 7-Å layers thick. High-resolution images of the sphere walls reveal a 2-layer structure similar to that of kaolinite. A calculated diffraction pattern based on a model of 4 concentric shells of ferric kaolinite structure matches the observed pattern quite closely. Some other hisingerites, notably that from Bellevue King Mine, Idaho, show 10-Å layers as well as 7-Å layers, and this hisingerite has a CEC of 32 meq/100 g and a weak 15.5-Å X-ray reflection in addition to a pattern similar to Riddarhyttan hisingerite. It is concluded that hisingerite is a curved ferric 7-Å 1:1 layer silicate analogous to halloysite, and that many of the hisingerites reported in the literature contain admixed nontronite.

The cation exchange capacities (CEC) and extractable cations in smectite, corrensite and palagonitized glass from hydrothermally-altered pillow lavas and hyaloclastite breccias were measured by both bulk wet chemical and in situ microanalytical techniques. Smectite has CEC's between 60 and 120 meq/100 g, palagonitized glass between 30 and 60 meq/100 g, and corrensite approximately 35 meq/100 g as determined by the in situ CsCl-exchange method. These experiments generally verify that Cs exchanges for those cations that are presumed (from the stoichiometry implied by microprobe analyses) to occupy interlayer sites in sheet silicates. Results of conventional CEC determinations are consistent with those determined by the in situ experiments: the individual microanalytical values for smectite and palagonitized glass bracket the bulk CEC values. The in situ experiments imply that Mg is the major extractable cation in smectite, Ca in corrensite, and both Mg and Ca in the palagonitized glass. We speculate that discrepancies between the equivalents of extractable cations predicted from elemental analysis and the equivalents of Cs sorbed may be due to the presence of charge-balancing protons that are not detected by the microprobe analyses. The sum of equivalents of cations extracted by NH4-acetate is about the same as the CEC determined by both the in situ and the bulk methods. Cation proportions indicated by NH4-acetate extractions from bulk samples are also generally consistent with the in situ results for all elements except Mg, which is a minor leachate of the NH4-acetate extractions in all the samples. To explain this discrepancy, we propose that 1) Mg may occupy structural sites within palagonitized glass, which inhibit its extraction by NH4 or Cs, and/or 2) there is a significant quantity of smectite, unsampled by the electron microprobe analyses, which contains insignificant interlayer Mg.

The effect of interlayering montmorillonite with different amounts of hydroxy aluminum cation on the cation exchange capacity (CEC) and the point of zero charge (PZC) of the clay was studied. The CEC decreased as the Al content of the clay increased. Both the CEC and the loss in the CEC were linearly dependent on the Al content, thus indicating the predominance of a single polynuclear interlayered species. Its composition is [Al6(OH)16.5]1.5+. Acid base titration of the interlayered montmorillonites produced values for the PZC in the range 4.5-5.9, increasing with the Al content of the materials. The values, however, did not represent real conditions of zero charge and some samples were still negatively charged at the determined PZC. The PZC values obtained by acid-base titration are thought to be adversely affected by secondary reactions involving the interlayered material with a concomitant release of soluble Al in amounts dependent on the pH and ionic strength.

Saponites were hydrothermally grown in the presence of amounts of NH4+, Na+, K+, Rb+, Ca2+, Ba2+, and Ce4+ equivalent with the CEC of the saponite (155 meq/100 g), with or without F−, at a temperature of 200°C for 72 hr. XRD and CEC data revealed the formation of a two-water-layer saponite with mainly Mg2+ as interlayer cation. Dehydration occurred between 25° and 450°C and dehydroxylation occurred in two steps between 450° and 790°C and between 790° and 890°C. The relatively small length of the b-axis between 9.151 and 9.180 Å is explained by considerable octahedral Al substitution (between 0.28 and 0.70 per three sites) and minor tetrahedral Al substitution (between 0.28 and 0.58 per four sites). Under the synthesis conditions applied in this study, less than 13% of the interlayer sites are occupied by Na+, K+, and Rb+; between 13.3% and 21% by Ca2+ and Ba2+; while NH4+ gives the highest value at 34%. The remaining sites are mainly filled by Mg2+. Ce4+ is not found in the saponite structure due to the formation of cerianite, CeO2. The presence of F− had little influence on the saponite composition. The formation of Mg-saponites is explained by a model in which an increased bayerite formation resulting in a higher octahedral Al3+ substitution and more Mg2+ in solution. Mg2+ is preferentially incorporated compared with the other interlayer cations due to its smallest ionic radius in combination with its 2 + charge.

Three ball clays (SP from England, TSMA from France and UK from the Ukraine) were characterized for their dry and wet colloidal properties. On the basis of X-ray diffraction and chemical analyses the clays were classified as kaolinite-rich clay, smectitic kaolinite-rich clay and illitic kaolinite-rich clay. The ζ (zeta) potential at the clay-water interface as a function of pH, in three different electrolytes, was investigated using an electroacoustic technique. Starting from measurements of dynamic mobility, the calculated ζ potential was found to be almost constant as a function of pH for the TSMA and UK clays, while it increased from −20 to −60 for the SP clay, when potassium nitrate was used as an electrolyte. The behavior of the three clays in calcium and magnesium nitrate was slightly different: SP showed a smaller increase in ζ potential, while a small deviation from the constant behavior of the UK clay was found. The results are explained in terms of the surrounding-ion atmosphere in light of the chemical-physical properties measured. Our results may well be of use to those involved in ceramic processing.

The effects of reaction time (2 to 72 h) and NH4+/A13+ molar ratio (1.6, 2.4 and 3.2) on the hydrothermal synthesis of ammonium-saponites are investigated. The gels are obtained by mixing powders, resulting in a stoichiometric composition, Mg3Si34Al0.6O10(OH)2, with aqueous ammonium solutions, with and without F, to result in initial NH4+/Al3+ molar ratios of 1.6, 2.4 and 3.2. The solid bulk products are characterized by X-raydiffraction (XRD), X-ray fluorescence (XRF) and scanning electron microscopy (SEM) combined with energy-dispersive X-ray (EDX) analysis. The cation exchange capacity (CEC) is determined with an ammonia selective electrode and the pH of the water from the first washing is measured. Ammonium-saponite is formed rapidly within 16 h. A higher NH4+/A13+ molar ratio and the presence of F facilitate the crystallization of saponite. Small metastable amounts of bayerite, Al(OH)3, are present at low NH4+/A13+ molar ratios; after short reaction times, they disappear. During the first 4 h, the pH decreases rapidly, then drops slowly to a constant level of approximately 4.6 after 60 h. With increasing reaction time, saponite crystallites grow in the ab directions of the individual sheets with almost no stacking to thicker flakes. The NH4+ CEC of the solid products increases strongly within the first 24 h. A maximum of 53.3 meq/100 g is observed. The saponite yield increases from approximately 25% after 2 h to almost 100% after 72 h.

Ammonium-saponite is hydrothermally grown at temperatures below 300°C from a gel with an overall composition corresponding to (NH4)0.6Mg3Si3.4Al0.6O10(OH)2. The synthetic saponite and coexisting fluid have been characterized by means of X-ray powder diffraction, X-ray fluorescence, Induced Coupled Plasma-Atomic Emission Spectroscopy, thermogravimetric analysis, transmission electron microscopy, CEC determination using an ammonia selective electrode, and pH measurement. In the crystallization model developed, crystallization started with the growth of individual tetrahedral layers with an aluminum substitution not controlled by the A1IV/A1VI ratio in the gel and hydrothermal fluid, on which the octahedral Mg layers can grow. During the synthesis, individual sheets stacked to form thicker flakes while lateral growth also took place. The remaining A1VI partly replaced ammonium as the interlayer cation.

The influence of water vapor on bentonites or smectites is of interest in many different fields of applied mineralogy such as nuclear-waste sealing or casting in the foundry industry. The water vapor affects the smectite surface and perhaps its structure probably leading to mostly unfavorable changes in its properties. In this first part of the present study, the influence of hot water vapor (200°C) on the physicochemical and mineralogical properties of smectite-group minerals was studied. After the steam treatment, turbidity measurements, methylene-blue sorption, water adsorption, and cation exchange capacity (CEC) were measured on both untreated and treated samples. Mineralogical changes were monitored by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) was used to measure O, Al, and Si. Only a few parameters showed differences between the untreated and vapor-treated samples. Sedimentation volumes (SV) decreased following the treatment. As shown by XRD and XPS, the crystalline structure of smectite remained unaffected by the steam treatment. Equivalent sphere diameters (ESD) were not affected systematically by the steam treatment. Differences in CEC values between untreated and treated samples were observed, but only for smectites with monovalent interlayer cations. From the variety of different measurements the conclusion of the present study was that steam treatment changes the charge properties at or near the smectite particle surface.

The objective of the study was to contribute to the understanding of the influence of the structure and the 2:1 layer dimension of smectites on cation exchange capacity (CEC) reduction and the hydration behavior of Li-saturated smectites after heating. Five montmorillonites extracted from bentonites of different provenance were saturated with Li+ and heated to 300°C. Initial montmorillonites and montmorillonites with reduced layer charge (RCM) were characterized by comprehensive mineralogical analysis supplemented by CEC measurements, surface-area measurements by Ar adsorption, and 7Li, 27Al, and 29Si magic-angle spinning nuclear magnetic resonance spectroscopy (MAS NMR). The CEC of the initial montmorillonites varied between 89 and 130 cmol(+)/kg while the CEC of the RCM prepared at 300°C varied between 8 and 25 cmol(+)/kg. The lateral dimension of the 2:1 layers varied between 70 and 200 nm. The greatest decrease in CEC was observed for the montmorillonite with the largest diameter of the 2:1 layers and the smallest decrease was observed for the montmorillonite with the smallest diameter of the 2:1 layers. 7Li MAS NMR revealed an axially symmetric chemical environment of the hydrated interlayer Li+ with ηΔ = 0 for the chemical shift anisotropy tensor for unheated montmorillonites with >33% tetrahedral layer charge (ξ). The chemical environment is typical of innersphere hydration complexes of interlayer Li+. An axially non-symmetric chemical environment of the interlayer Li+ with ηCS of close to one was observed for all RCM. While the remaining CEC of RCM prepared at 300°C reflected the variable CEC at the edges, and thus the lateral size or aspect ratio of the 2:1 layers, the hydration complex of interlayer Li+ was strongly determined by the isomorphic substitutions in the dioctahedral 2:1 layers.

Two industrial bentonites, IBECO SEAL-80 and TIXOTON TE, have been proposed as potential backfill material in the German Asse salt dome, a test field for the disposal of low- to medium-grade active nuclear waste. Considering the unlikely but possible case of a barrier breakdown with infiltration of a highly concentrated salt brine, the physicochemical stability and material behavior of these bentonites in a saturated salt brine (predominantly MgCl2) at 25°C were studied over the time period of 150 days. The results show that no mineral transformations occurred throughout the duration of the experiments and minor dissolution was only active during the first days. Some chemical properties, namely sorption capability and swelling, were reduced during contact with the salt brine, but could be reversed by removing the salt after treatment. Despite restriction of the CEC in the presence of salt solution, interlayer cation exchange reactions are still active in this environment. The long-term chemical stability of smectite in salt brine is predicted under these low-temperature conditions, but the increased permeability during aggregate formation could lead to physical breakdown of the backfill component.

Stevensite-like sauconite, with the general composition: ${\text{Si}}_4\left({\text{Zn}}_{3-x}{\square }_x\right){\text{O}}_{10}{\left(\text{OH}\right)}_2{R}_{2x}^{+}$\$\end{document}, where □ is a vacant site, was synthesized. The objective was to study the possible migration of some cations (Li+ and Zn2+) within such trioctahedral smectites, under heating, following the so-called ‘Hofmann-Klemen’ (HK) effect. The initial gel was divided into five aliquots and placed in teflon-coated hydrothermal reactors with distilled water, and these were hydrothermally treated at 80, 100, 120, 150, and 200°C, respectively, over 30 days. X-ray diffraction (XRD) analysis confirmed that the samples synthesized were smectites. The number of vacant sites (x) per half unit cell (O10(OH)2) ranged from nearly 0 to 0.23 but no simple relationship was established between x and the temperature of synthesis. The samples were Li+- and Zn2+-saturated, and heated overnight at 300°C (HK treatment). Cation exchange capacity measurements were made by Fourier transform infrared spectroscopy (FTIR) on ${\text{NH}}_4^{+}$\$\end{document}-saturated samples. After LiHK treatment, the structural formula of samples could be expressed as: ${\text{Si}}_4{\text{Zn}}_{\left(3-x\right)}{\text{Li}}_x{\text{O}}_{10}{\left(\text{OH}\right)}_2{\text{NH}}_{4x}^{+}$\$\end{document}, while after ZnHK treatment, it could be expressed as: Si4Zn3O10(OH)2. Analysis by XRD and FTIR showed that the samples moved from a Zn-stevensite-like structure to Zn-talc-like structure after treatment with ZnHK. These results are interpreted asevidence that Zn2+ (and Li+) migrated into the previously vacant sites under HK treatment.

Purification processes performed on natural clays to select specific clay minerals are complex and expensive and can lead to over-exploitation of some deposits. The present study aimed to examine physicochemical (mineralogy, morphology, size, surface charge, chemical composition, cation exchange capacity [CEC], and pH) and hydration (swelling, wettability, water sorption, and rheological behavior) properties of three native clays from Italian deposits for potential pharmaceutical and cosmetic uses due to the presence of phyllosilicate minerals. Particular emphasis was placed on energy dispersive X-ray (EDX) microanalysis coupled with the ‘cesium method’ to assay clay elemental composition and CEC. One bentonite of volcanic origin (BNT) and two kaolins, one of hydrothermal origin (K-H) and another of lacustrine-fluvial origin (K-L), were evaluated in comparison with a commercial, purified bentonite. The CEC assay revealed the complete substitution of exchangeable cations (Na+ and Ca2+) by Cs+ in BNT samples and CEC values consistent with those of typical smectites (100.64 ± 7.33 meq/100 g). For kaolins, partial substitution of Na+ cations occurred only in the K-L samples because of the interstratified mineral component which has small CEC values (11.13 ± 5.46 meq/100 g for the K-H sample and 14.75 ± 6.58 meq/100 g for the K-L sample). The degree of isomorphous substitution of Al3+ by Mg2+ affected the hydration properties of BNT in terms of swelling, water sorption, and rheology, whereas both of the poorly expandable kaolins exhibited significant water-adsorption properties. The EDX microanalysis has proved to be of considerable interest in terms of providing more information about clay properties in comparison with other commonly used methods and to identify the role played by both chemical and mineralogical composition of natural clays for their appropriate use in pharmaceutical and cosmetic fields.

The sedimentary series from Academician Ridge, Lake Baikal, eastern Siberia, was examined using cation exchange capacity (CEC) to estimate the amount of expandable clay minerals (ECM) and high-temperature X-ray diffraction (HT-XRD) to determine their basic classification. The comparison of the magnetic susceptibility (MS) at sub-millennial resolution and the δl8O record of a reference Atlantic core (ODP 980) was used to create an age model. The most closely studied part of the series covered the major part of the last glacial cycle (120–20 ky BP). The HT-XRD analysis is based on monitoring the course of ECM dehydration with 5°C steps between 25 and 250°C and enabled us to improve the discrimination between ECM, chlorite and micas. The CEC obtained at millennial resolution showed that the neoformation of ECM in warmer periods of the last interglacial was either insignificant or fully compensated by their dissolution or dilution. The CEC record was correlated with the main climatic stages in the period studied. Both MS and CEC records reflected the environmental changes at about millennial resolution, including climatic instabilities between 117 and 73 ky BP (late MIS5).

The Boom Clay in northern Belgium has been studied intensively over recent decades as a potential host rock in the context of disposal of radioactive waste. One of the parameters of interest is the cation exchange capacity (CEC) as it is related to the sorption potential of radionuclides to the clay host rock. In the past, the CEC was determined using various methods on a limited number of samples, leading to significant variations. To constrain the CEC of the Boom Clay better, a sample set covering the entire stratigraphy was measured using the quick copper(II) triethylenetetramine method. Part of the sample set was also measured using the cobalt(III) hexamine method, as a quality control for the results of the former method. In addition, the exchangeable cation population of the Boom Clay was quantified systematically for the first time and these results were compared to the in situ pore-water chemistry, indicating a strong coupling between the pore-water composition and the exchangeable sites of clay minerals.