In Russia, the Iskra-6 laser facility with pulse energy of up to 300 kJ and nanosecond pulse duration was being planned (Kirillov et al., 2000). The possibility of thermonuclear ignition with this laser energy was a goal of the theoretical investigation at RFNC-VNIITF. Results of one-dimensional (1D) and two-dimensional (2D) modeling of indirect-driven targets for ignition on the Iskra-6 laser facility are presented. Sensitivity of cryogenic single-shell and non-cryogenic double-shell targets to radiation flux non-uniformity and shells roughness are studied.

This paper reports on a novel approach for producing high energy femtosecond pulses without external amplification. The so-called chirped-pulse oscillator (CPO) concept is based on an extended-cavity oscillator, operating at small net positive intracavity group delay dispersion (GDD), over a broad spectral range by the use of chirped multilayer mirrors. The resultant chirped picosecond pulses are compressed by a dispersive delay line external to the laser cavity. Utilizing this technique, sub-30 fs pulses with an energy exceeding 200 nJ at a repetition rate of 11 MHz were produced. The demonstrated peak power in excess of 5 MW is the highest ever achieved from a cw-pumped laser and is expected to be scaleable to tens of megawatts by increasing the pump power and/or decreasing the repetition rate. The demonstrated source allows micromachining of any materials under relaxed focusing conditions.

At the start of a new volume I want to take the opportunity to thank the associate editors and the editorial board members whose terms ended recently for their many years of service to the scientific community and to this journal especially. I personally had a lot of help from all of them, and I dare to ask for their continued support for this journal. The attentive reader may notice quite a change in the editorial team. Therefore this is also the opportunity to welcome the new board members and to wish them success for their editorial work.

This issue of Laser and Particle Beams includes papers presented at the Workshop on “Fast High Density Plasma Blocks Driven by Picosecond Terawatt Lasers” held at the University of Western Sydney, Campbelltown Campus, Australia from 1–4 December 2004.

The present 28th ECLIM in Rome is a continuation of the series of conferences that started in Frascati, Italy in 1966. These conferences deal with the interdisciplinary subjects of laser interaction with matter, related not only to basic science but also to a wide range of applications. ECLIM is an independent scientific conference, free of any institutional or political influence, keeping science without boundaries.

This new project relies on the capabilities collocated at Los Alamos in the Trident laser facility of long-pulse laser drive, for laser-plasma formation, and high-intensity short-pulse laser drive, for relativistic laser-matter interaction experiments. Specifically, we are working to understand quantitatively the physics that underlie the generation of laser-driven MeV/nucleon ion beams, in order to extend these capabilities over a range of ion species, to optimize beam generation, and to control those beams. Furthermore, we intend to study the interaction of these novel laser-driven ion beams with dense plasmas, which are relevant to important topics such as the fast-ignition method of inertial confinement fusion (ICF), weapons physics, and planetary physics. We are interested in irradiating metallic foils with the Trident short-pulse laser to generate medium to heavy ion beams (Z = 20–45) with high efficiency. At present, target-surface impurities seem to be the main obstacle to reliable and efficient acceleration of metallic ions in the foil substrate. In order to quantify the problem, measurements of surface impurities on typical metallic-foil laser targets were made. To eliminate these impurities, we resorted to novel target-treatment techniques such as Joule-heating and laser-ablation, using a long-pulse laser intensity of ∼ 1010 W/cm2. Our progress on this promising effort is presented in this paper, along with a summary of the overall project.

Basic properties of generation of high-current ion beams using the skin-layer ponderomotive acceleration (S-LPA) mechanism, induced by a short laser pulse interacting with a solid target are studied. Simplified scaling laws for the ion energies, the ion current densities, the ion beam intensities, and the efficiency of ions' production are derived for the cases of subrelativistic and relativistic laser-plasma interactions. The results of the time-of-flight measurements performed for both backward-accelerated ion beams from a massive target and forward-accelerated beams from a thin foil target irradiated by 1-ps laser pulse of intensity up to ∼ 1017 W/cm2 are presented. The ion current densities and the ion beam intensities at the source obtained from these measurements are compared to the ones achieved in recent short-pulse experiments using the target normal sheath acceleration (TNSA) mechanism at relativistic (>1019 W/cm2) laser intensities. The possibility of application of high-current ion beams produced by S-LPA at relativistic intensities for fast ignition of fusion target is considered. Using the derived scaling laws for the ion beam parameters, the achievement conditions for ignition of compressed DT fuel with ion beams driven by ps laser pulses of total energy ≤ 100 kJ is shown.

This paper summarizes experimental results on the injection and transport of intense, wide cross-section H+ plasma (PB), and ion beams (IB), in vacuum and ambient H+ plasma across an applied B-field. The injection of plasma and ion beams into magnetic confinement devices have the potential to heat and support current in these systems (e.g., field-reversed configurations). The translational energies of the PB and IB ranged between Epb = 60 to 120 eV and EIB = 60 to 120 keV, with temperatures and densities in the range of Tb ∼ 2 to 10 eV, nb ∼ 1012 to 1013 cm−3, and Tb ∼ 200 eV, nb 1010 to 1011 cm−3, respectively. Compared to earlier studies (Peter et al., 1979; Wessel et al., 1988, 1990), this research extends the experimental parameter space to higher beam current densities (up to 30 A/cm2) and higher B-field strengths up to 1.6 kG. The PB and IB were both about 10 cm in diameter at the injection port, and the ratio of beam specific energy to ambient B-field specific energy, β, was in the range of 0.1 to 10. Ratios of beam Larmor radius to beam size, ρ, ranged from 10−1 to 1 and 1 to 10 for the PB and IB, respectively. Cross B-field propagation of the PB in vacuum was undeflected as a whole with a sharp increase (one order or more) in the current density of the central beam core at B-field levels > 1 kG accompanied by a significant loss of beam peripheral layers, beam “braking” and preferential beam expansion along the B-field lines. Cross B-field propagation of the PB in ambient plasma did not differ substantially from the case without B-field, that is, no deflection of the PB as a whole, which could be due to an insufficient neutralization of the induced E-field inside the PB. Cross B-field propagation of the IB in ambient plasma followed a single particle trajectory deflection with a simultaneous significant loss of IB intensity without any detectable bunching, indicating an adequate shorting of the polarization E-field inside the IB.

This paper represents the results of a study of angular distribution of laser produced ions (LPI) of Al, Cu, and Ag. The angular distribution is studied by CR-39 (SSNTD) and ion assisted sputtering experiments. A Q-Switched Nd:YAG laser (1.064 μm, 1.1 MW) with 10 mJ pulsed energy was used to produce the Ag ions, which were detected by CR-39 detector mounted at −17.5°, 0°, 17.5°, 30°, 60°, and 90° from the normal to the target placed at a distance of 9 cm from the target. Etched CR-39 detectors then observed under the Motic DMB Series optical microscope. A bunch of ions was detected along the normal of target due to self generated collimation of ions. This is termed as Forward Peaking of Laser Produced Ions. Similar results were also observed from sputtering of polished Al substrate by laser produced ions of Cu and Sputtering of polished Cu substrate by laser produced ions of Al. The surface morphology of the ion irradiated samples were observed under the Scanning Electron microscope (SEM) S 300 Hi-tech. Formation of a circular damage on the surface of the substrates by irradiation conforms the ions collimation along the normal or Forward Peaking of ions.

A two-dimensional (2D) multigroup radiation transfer hydrodynamics code LARED-R-1 is used to simulate a supersonic wave experiment performed earlier by the Livermore group. The main result is that, contrary to the conclusion of Back et al. (2000a), the average-atom opacity model is sufficient to explain the obtained experimental results, provided that an adequate description of the radiation transport was used. The simulation results from LARED-R-1 show the spectrum of radiation in foam with radius and length of several optical depths is not in Planckian distribution and the angular intensity distribution is anisotropic.

We address the issues of collective stopping for intense relativistic electron beams (REB) used to selectively ignite precompressed deuterium + tritium (DT) fuels. We investigate the subtle interplay of electron collisions in target as well as in beam plasmas with quasi-linear electromagnetic growth rates. Intrabeam scattering is found effective in taming those instabilities, in particular for high transverse temperatures.

It is shown that the effective hot electron temperature, Thot, associated with the energetic electrons produced during the interaction of an ultra-intense laser with thin solid targets is dependent on the thickness of the target. We report the first direct experimental observations of electron energy spectra obtained from laser-solid interactions that indicates the reflexing of electrons in thin targets results in higher electron temperatures than those obtained in thick target interactions. This can occur for targets whose thickness, xt, is less than about half the range of an electron at the energy associated with the initial effective electron temperature, provided the laser pulse length is at least cτp > 2xt. A simple theoretical model that demonstrates the physical mechanism behind this enhanced heating is presented and the results of computer simulations are used to verify the model.

The energy transfer rate between the lattice and electrons in strongly nonequilibrium electron-phonon system of crystalline aluminum created by ultrashort femtosecond laser pulse is calculated in the frame of two-temperature model for a wide range of electron temperature. It is shown that the energy, transmitted from electrons to the lattice per unit volume of the crystal per unut time strongly increases when taking into account the umklapp processes in the electron-phonon scattering.

The compression of a cryogenic hydrogen cylindrical sample contained in a hollow gold target driven by an intense co-axial uranium beam has been studied. The ion distribution is assumed to be Gaussian in space and parabolic in time. The hydrodynamics of the target is analyzed by means of one- and two-dimensional numerical simulations. A parametric study is performed to achieve the maximum average hydrogen density and temperature as a function of the sample radius, total number of ions and spread of the spatial ion distribution. A window in the beam-target parameters for which hydrogen compression is higher than a factor of 10 and temperature is below 0.2 eV has been found by considering a single bunch that contains 2 × 1011 uranium ions delivered in 100 ns. In this range of high densities and low temperatures, it is expected that hydrogen may become metallic.

We have developed a compact, 14.7 nm, sub-5 ps X-ray laser source at Lawrence Livermore National Laboratory (LLNL) together with a Mach-Zehnder type diffraction grating interferometer built at Colorado State University for probing dense, high intensity laser-produced plasmas. The short wavelength and pulse length of the probe reduces refraction, absorption effects within the plasma and minimizes plasma motion blurring. This unique diagnostic capability gives precise two-dimensional (2D) density profile snapshots and is generating new data for rapidly evolving laser-heated plasmas. A review of the results from dense, mm-scale line focus plasma experiments will be described with detailed comparisons to hydrodynamic simulations.

Propagation of ultrashort intense laser pulses in a plasma Bragg grating induced by two counterpropagating laser pulses has been investigated. Such a plasma grating exhibits an ultrawide photonic band gap, near which strong dispersion appears. It is found that the grating dispersion dominates the dispersion of background plasma by several orders of magnitude. Particle-in-cell (PIC) simulations show light speed reduction, pulse stretching, and chirped pulse compression in the plasma grating. The nonlinear coupled-mode theory agrees well with the PIC results. Because the plasma grating has a much higher damage threshold than the ordinary optical elements made of metal or dielectric, it can be a novel tool for controlling femtosecond intense laser pulses.

Generation of high speed dense plasma blocks is well known from hydrodynamic theory and computations (PIC) with experimental confirmation by Badziak et al. (2005) since ps laser pulses with power above TW are available. These blocks may be used for fusion flame generation (thermonuclear propagation) in uncompressed solid state deuterium and tritium for very high gain uncomplicated operation in power stations. Hydrodynamic theory from computations from the end of 1970s to recent, genuine two fluid computations support the skin layer accelerations (SLA), by nonlinear (ponderomotive) forces as measured now in details under the uniquely selected conditions to suppress relativistic self-focusing by high contrast ratio and to keep plane geometry interaction. It is shown how the now available PW-ps laser pulses may provide the very extreme conditions for generating the fusion flames in solid state density DT.

The possibilities of producing ultrahigh-current-density ps ion fluxes by the skin-layer interaction of a short (≤ 1ps) laser pulse with plasma were studied using two-fluid hydrodynamic simulations, and the time-of-flight measurements. Backward-emitted ion fluxes from a massive (Au) target as well as forward-emitted fluxes from various thin foil targets irradiated by a 1-ps laser pulse of intensity up to 2 × 1017 W/cm2 were recorded. Both the simulations and the measurements confirmed that using the short-pulse skin-layer interaction of a laser pulse with a thin pre-plasma layer in front of a solid target, a high-density collimated ion flux of extremely high ion current density (∼ 1010 A/cm2 close to the target), can be generated at laser intensity only ∼ 1017 W/cm2. The ion current densities produced by this way were found to be comparable to (or even higher than) those estimated from recent short-pulse experiments using a target normal sheath acceleration mechanism at relativistic laser intensities. The effect of the target structure on the current densities and energies of forward-emitted ions is demonstrated.

In this paper, we suggest the creation of a nanoparticles and nanotubes by using the interaction of a femtosecond laser with a solid target in a vacuum. A simple model is used to predict the optimal target and the laser parameters for the production of efficient nanoparticles. At the Soreq laboratory, experiments are performed with aluminium and carbon targets using a femtosecond laser. The irradiated targets are composed of either a thin layer of aluminium or of carbon, deposited on a transparent heat-insulating glass substrate. The nanoparticle debris is collected on a silicone wafer for X-ray diffraction (XRD), for scanning electron microscopy (SEM), and for atomic force microscopy (AFM). For transmission electron microscopy (TEM), the debris is caught on a copper grid covered on one side with a carbon membrane. Our experiments confirm the creation of crystal nanoparticles for aluminium and nanotubes for carbon experiments.

Due to their particular properties (low emittance, short duration, and large number density), the beams of multi-MeV protons generated during the interaction of ultraintense (I > 1019 W/cm2) short pulses with thin solid targets are suited for use as a particle probe in laser-plasma experiments. When traversing a sample, the proton density distribution is, in general, affected by collisional stopping, scattering and deflections via electromagnetic fields, and each of these effects can be used for diagnostic purposes. In particular, in the limit of very thin targets, the proton beams represent a valuable diagnostic tool for the detection of quasi-static electromagnetic fields. The proton imaging and deflectometry techniques employ these beams, in a point-projection imaging scheme, as an easily synchronizable diagnostic tool in laser- plasma interactions, with high temporal and spatial resolution. By providing diagnostic access to electro-magnetic field distributions in dense plasmas, this novel diagnostics opens up to investigation a whole new range of unexplored phenomena. Several transient processes were investigated employing this technique, via the detection of the associated electric fields. Examples provided in this paper include the detection of pressure-gradient electric field in extended plasmas, and the study of the electrostatic fields associated to the emission of MeV proton beams in high-intensity laser-foil interactions.